Brands
Categories


Categories A-Z
Manufacturers A-Z
Brands A-Z


ENGINE COMPONENTS
FUEL INJECTORS & ACCESSORIES
FUEL PUMPS & ACCESSORIES
HARDWARE
HOSE, FITTINGS, ADAPTERS, ACCESSORIES
LIGHTING SOLUTIONS
PROMOTIONAL ITEMS
SILICONE PRODUCTS
TANKS, CANS, CELLS ETC.
THERMAL SOLUTIONS
TOOLS
VEHICLE ELECTRONICS
WIRE HARNESSES & SOLUTIONS
WIRING COMPONENTS & AIDS


Accufab
Bosch
Continental
Delphi Electronics
Delphi Fueling Products
Delphi Injectors
Edelbrock
Fragola Performance Systems
Gates
GDE Corp.
Goodridge
Handy & Harman
HBD Industries
Hobbs
Lingenfelter Performance
Littlefuse
Magneti Marelli
Marshall Instruments
OTC
Perma-Cool
Racetronix
Siemens (Continental)
Stancor
Standard Motor Products
Techflex
More...


Accel
Autofuse
Barricade
FIREFLEX
FLEXO
Fragola
Goodridge
Hobbs
Insultherm
Mallory
Racetronix
Russell
THERMALSHIELD
Thermoid
Turbine-Tech
Uniburr
Walbro



Browse other Categories here:
HOME  FUEL INJECTORS & ACCESSORIES  Fuel Injectors - Low Impedance

  55 lb/hr Low-Z Injector    


Click for larger picture
List Price: $55.00
Our Price: $49.50 per EACH
Buy in:
Qty:    Add Item to Cart
Add to Wish List
Item Code: 01D139x
Weight: 85.50GM
Brands: Racetronix
Manufacturers : Standard Motor Products
Stock: Yes
Model: INJL55
Categories: Fuel Injectors - Low Impedance
Static Flow lb/hr (n-Heptane): 52
Static Flow cc/min: 576
Static Flow Tolerance +/-%: 4
Dynamic Flow (mg/pulse): 12.00
Dynamic Flow Tolerance +/-%: 4
Coil Resistance Ohms: 2.2
Coil Resistance Tolerance +/- Ohms: .15
Peak/Hold Current Amps: 4A / 1A
Spray Pattern: Tri-Cone



01D139x

 

FLOW-MATCHED 1% INJECTORS ARE SOLD IN PACKS VIA THE 'BUY IN' DROP-DOWN MENU ABOVE.

INJECTORS SOLD AS EACH ARE NOT FLOW-MATCHED (LISTED FACTORY TOLERANCE APPLIES)

TECHNICAL INFORMATION

Dynamically flowed and grouped to within 1% tolerance using Racetronix custom injector flow bench when purchased in packs.
All tests run with n-Heptane @ 20oC (+/-1oC), 3.0 Bar (+/-0.01 Bar), 14VDC (+/-0.05VDC), saturated driver with RC cutoff.

Injector flow rates are based on testing with n-Heptane test solvent (0.6855 g/ml). U.S. EPA emission test gasoline 40CFR86.113 (0.735g/ml) flows in most common injector designs at about a 3 to 4% higher rate than n-Heptane. A ratio of 1.035:1 can be used when converting the flow specifications above.

This low-impedance injector is designed to work with peak and hold injector drivers typically found in aftermarket ECM/PCMs as well as dedicated injector driver modules sold by Racetronix..

TYPICAL APPLICATIONS

High-performance aftermarket

ADDITIONAL INFORMATION


Top feed disc injectors use a small disc with six holes around its circumference. The disc rests on a short chimney that surrounds a metering hole. As the disc is raised off the chimney by magnetic force, fuel flows through the holes in the disc, over the walls of the chimney, and out the metering hole to form a full, finely atomized cone.

  • The flat mating surface ensures that no excess fuel is present to evaporate and therefore, no deposits or clogging can occur
  • Longer service life
  • High-speed disc action allows wider dynamic flow range for improved idling
    Quieter operation
  • Revolutionary disc design resists build up deposits which can affect fuel flow
  • No Fuel leakage for quicker starts
  • Compatible with alternative fuels (i.e. E85, Methanol)
  • Grease supplied to lubricate o-rings prior to installation
 



Wish List
 




©Racetronix, All rights reserved.