Welcome to Racetronix
Welcome to Racetronix  |  All prices indicated are in USD($)  905-477-7014  |   Help   |  Catalogs  |  About Us

Adapter, -6 AN JIC Male to 5/16” Barb Receptor

Quick Overview

  • Adapter, -6 AN JIC male to 5/16" barb receptor
  • Converts barbed tubes and nipples to AN
  • Hex collar compresses O-ring under the barb
  • Measure barb diameter and position first
  • E85 compatible, black anodized 6061-T6 aluminum

Show More
Item #: ADF-6J56FB

$13.15

per EACH (USD)
This is an obsolete Item
 
 
 In Stock & Ready to Ship

Adapter, -6 AN JIC Male to 5/16” Barb Receptor

Converts a 5/16" barbed tube or nipple to a -6 AN JIC male, without cutting or flaring.

The Racetronix ADF-6J56FB turns a plain 5/16" barbed tube or formed nipple into a -6 AN JIC male (37° flare). It works like a compression fitting: slide the hex collar over the barb, push the barb into the body and tighten the collar. The collar compresses an O-ring that catches under the lip of the barb and seals around it.

It is a clean way to convert parts that only have a push-on hose barb, such as heater cores, power steering pump suction lines, vacuum devices and formed metal lines on older cars, to AN hose and fittings.

Key features

  • -6 AN JIC male (37° flare).
  • 5/16" barb receptor: hex collar and O-ring seal under the barb.
  • No cutting or flaring of the original tube.
  • E85 compatible.
  • 6061-T6 aluminum, black anodized.
Check your barb before ordering

This fitting does not suit every barb. The barb must pass through the opening in the hex collar, and its lip must be shaped so the O-ring can compress underneath it. Measure the barb's largest diameter and the distance from the end of the tube or part to the barb before you order. The AN end seals metal to metal on its 37° flare, not on the threads. Do not put Teflon tape or thread sealant on it.

Specifications

Part numberADF-6J56FB
JIC end-6 AN JIC male, 9/16"-18 thread, 37° flare
Barb end5/16" barb receptor, hex collar with O-ring seal
Material6061-T6 aluminum, black anodized
Fuel compatibilityGasoline and E85

Lookup chart

Every part in this series. This part is highlighted. Click a column heading to sort by it; click again to reverse. On a phone, swipe the chart sideways.

Part numberAN JIC maleBarb size
ADF-6J56FB-6 AN5/16"
ADF-6J38FB-6 AN3/8"
ADF-8J56FB-8 AN5/16"
ADF-8J38FB-8 AN3/8"
ADF-8J12FB-8 AN1/2"
ADF-8J15MFB-8 AN15 mm
ADF-8J58FB-8 AN5/8"
ADF-10J12FB-10 AN1/2"
ADF-10J15MFB-10 AN15 mm
ADF-10J58FB-10 AN5/8"
ADF-10J34FB-10 AN3/4"
ADF-12J58FB-12 AN5/8"
ADF-12J34FB-12 AN3/4"

Frequently asked questions

Will it fit my barb?

Only if the barb fits through the hex collar opening and has a lip the O-ring can seal under. Measure the largest diameter of the barb and how far it sits from the end of the tube or part. Multi-barb and single-barb nipples both work if the first barb meets these conditions. If you are not sure, email [email protected] with your measurements before you order.

How do I install it?

Remove the hex collar and slide it over the barbed tube, push the tube into the fitting body as far as it goes, then thread the collar on and tighten it. The collar squeezes the O-ring under the barb. Connect your -6 AN hose end to the JIC end.

Do I need a hose clamp?

No. The O-ring under the barb lip does the sealing and holding. No clamp or rubber hose is needed on the barb.

Is it E85 compatible?

Yes. It is made from 6061-T6 aluminum and black anodized, and works with gasoline and E85.

Questions and support

Not sure which fitting your build needs? Email [email protected] before you order.

Racetronix provides technical support to verified customers through our support forum, not by phone or email. Please request forum access when you place your order so your account is approved before your parts arrive. The forum is moderated, open 24/7, and holds a knowledge base going back to 1999.

© 2026 Racetronix. All rights reserved. | Part No: ADF-6J56FB | Revision: Bravo