Crush Washer, M10, 10.2 x 16 x 1.5 mm, 901 Aluminum
Quick Overview
- Aluminum crush washer, M10
- 10.2 x 16 x 1.5 mm
- Soft 901 aluminum seals against flat faces
- For fittings, banjo bolts and drain plugs
- Sold each
Show More
$0.59
per EACH (USD)Crush Washer, M10, 10.2 x 16 x 1.5 mm, 901 Aluminum
Soft 901 aluminum crush (sealing) washer for M10 threads: 10.2 x 16 x 1.5 mm. Seals a straight-thread fitting or bolt against a flat face.
The Racetronix FIT-CWM10AL is a soft aluminum crush washer for M10 threads. Tightened between a straight-thread fitting, banjo bolt or drain plug and a flat face, it deforms slightly to fill surface marks and make a fluid-tight seal. Fit a new one each time the joint is taken apart.
Key features
- For M10 threads: 10.2 mm ID.
- 10.2 x 16 x 1.5 mm.
- 901 aluminum: soft enough to crush and seal at normal torque.
- Single use: replace when the joint is remade.
Crush washer chart: all sizes
All Racetronix aluminum crush washers sold individually. Click a column heading to sort.
| Part | Fits thread | ID | OD | Thickness |
|---|---|---|---|---|
| FIT-CWM06AL | M6 | 6.2 mm | 12.1 mm | 1.5 mm |
| 392-999209 | M8 | 8 mm | - | - |
| FIT-CWM08AL | M8 | 8.2 mm | 14.1 mm | 1.5 mm |
| FIT-CWM10AL | M10 | 10.2 mm | 16 mm | 1.5 mm |
| 392-999212 | M12 | 12 mm | - | - |
| FIT-CWM12AL | M12 | 12 mm | - | 1.5 mm |
| FIT-CWM14AL | M14 | 14.2 mm | 20.1 mm | 1.5 mm |
| FIT-CWM16AL | M16 | 16.2 mm | 22.1 mm | 1.5 mm |
| FIT-CWM18AL | M18 | 18 mm | - | 1.5 mm |
| FIT-CWM20AL | M20 | 20 mm | - | 1.5 mm |
| FIT-CWM22AL | M22 | 22 mm | - | 1.5 mm |
| FIT-CWM24AL | M24 | 24 mm | - | 1.5 mm |
| 392-999206 | -12 AN (1-1/16") | 1-1/16" | - | - |
Specifications
| Part number | FIT-CWM10AL |
| Fits thread | M10 |
| Inside diameter | 10.2 mm |
| Outside diameter | 16 mm |
| Thickness | 1.5 mm |
| Material | 901 aluminum |
| Sold | Each |
Frequently asked questions
Can I reuse a crush washer?
No. Once crushed it has taken the shape of the old joint and may not seal again. Fit a new washer.
Aluminum or PTFE?
Aluminum crush washers suit most fuel, oil and coolant joints. For AN sizes, PTFE washers are an alternative that seals at lower torque; see TWSHR-SET.
Questions and support
Questions before you order? Email [email protected].
Racetronix provides technical support to verified customers through our support forum, not by phone or email. Please request forum access when you place your order so your account is approved before your parts arrive. The forum is moderated, open 24/7, and holds a knowledge base going back to 1999.




