Welcome to Racetronix
Welcome to Racetronix  |  All prices indicated are in USD($)  905-477-7014  |   Help   |  Catalogs  |  About Us

Techflex Insultherm Spark Plug Boot Sleeve, 7-1/2”, Natural

Quick Overview

  • Techflex Insultherm spark plug boot sleeve, 7-1/2 in, Natural
  • Double-thick braided fiberglass, triple-thick at the sewn end
  • Protects plug boots from heat up to 1,200 degrees F
  • Can rest directly on the header; fits straight and right-angle boots
  • Sold each

Show More
Item #: 299-FCN0.75-NT  MPN : FCN0-75-NT

$3.32

per EACH (USD)
This is an obsolete Item
 
 
 In Stock & Ready to Ship

Techflex Insultherm Spark Plug Boot Sleeve, 7-1/2" Long, Natural

Double-thick braided fiberglass sleeve that slips over the plug wire boot: protects it from header heat up to 1,200°F (649°C) and can rest right on the pipe.

Techflex Insultherm spark plug boot sleeve, natural

These are Techflex Insultherm spark plug boot sleeves: double-thickness braided fiberglass, triple-thick at the sewn end, 3/4" in diameter and 7-1/2" long. Racetronix is a Techflex distributor. Slip one over any plug wire and boot, straight or right-angle, and the boot is protected from engine and header heat up to 1,200°F (649°C). Once fitted, the maker says the sleeve needs no clearance from hot surfaces and can rest directly on a header. This version has no ring. Sold each.

Key features

  • Protects plug boots from heat up to 1,200°F (649°C); can touch the header.
  • Double wall, triple-thick at the sewn end.
  • Non-conductive, will not support combustion, resists engine chemicals; UL VW-1.
  • Extreme abrasion resistance in the maker's test.
  • 7-1/2" long: covers straight and right-angle boots. Sold each.

Boot sleeves we stock

PartInner ringColourLengthDiameterWall
299-FCN0.75-BKNoBlack7-1/2"3/4"0.085"
299-FCN0.75-NTNoNatural7-1/2"3/4"0.085"
299-FCU0.75-BKYesBlack7-1/2"3/4"0.085"
299-FCU0.75-NTYesNatural7-1/2"3/4"0.085"

All four are the same length, diameter and rating; choose by colour and whether you want the inner ring. Sold each.

Equivalents: other brands' plug boot sleeves

Shopping for another brand? These are fiberglass plug boot sleeves. Most are 1" across and 6" to 7" long, so they are near equivalents rather than identical.

Our partInstead of (brand)Their part numberDescriptionMatch
299-FCN0.75-BKDEI010510 / 010509 / 010518Ringless boot sleeve, 7", 2 / 4 / 8 packNear equivalent
299-FCN0.75-BKHeatshield Products400204 / 400804Double-wall boot sleeve, black, 1" x 6", 2 / 8 packNear equivalent
299-FCN0.75-NTHeatshield Products400200 / 400800Double-wall boot sleeve, tan, 1" x 6", 2 / 8 packNear equivalent
299-FCU0.75-BKDEI010511 / 010512Boot sleeve with reinforcement ring, black, 1" x 6"Near equivalent
299-FCU0.75-NTDEI010501 / 010507 / 010502Boot sleeve with reinforcement ring, silver, 1" x 6", 2 / 4 / 8 packNear equivalent

Other brands' names and part numbers are their owners' trademarks, listed only to help you compare. Check sizes against your application.

Specifications

ConstructionResin-coated braided fiberglass, double wall, triple-thick at the sewn end
Length7-1/2" (191 mm)
Diameter3/4" (19 mm)
Wall0.085" (2.2 mm)
Inner ringNo
TemperatureUp to 1,200°F (649°C)
FlammabilityUL VW-1; will not support combustion; halogen free
ColourNatural
Sold asEach

Fitting boot sleeves

  1. Pull the plug wire off the plug by its boot, not the wire.
  2. Slide the sleeve over the boot so it covers the boot fully.
  3. Refit the wire to the plug and check the boot has clicked home.
  4. Do one cylinder at a time so the firing order stays right.

Which heat protection do I need?

Heat reaches a hose or wire in three ways, and each needs a different kind of protection.

  • Radiant heat. A header or turbo throws heat out in every direction, like a stove element, and it reaches anything in line of sight. Reflective foil stops it best: the aluminized face bounces it back before it gets in.
  • Heat soak. Hot air and nearby hot parts warm a line slowly and steadily. Insulation stops it. Braided fiberglass traps thousands of tiny pockets of still air, the same way the insulation in a house wall does, and still air carries heat very poorly. Squash the fiberglass and the air goes, and most of the insulation with it.
  • Flame, sparks and splash. A burst line, a backfire or weld spatter. This needs a covering that will not burn: a silicone jacket or a non-flammable fibre.

Foil-over-fiberglass products combine the first two: the foil reflects, the fiberglass insulates. Nothing should rest against a bare header; wrap the header, shield the line, or both.

SituationUseWhy it works
The exhaust itself: headers, down pipes, turbo crossoversHeader wrapKeeps the heat inside the pipe, so far less of it radiates onto the hoses, wiring and bodywork around it. The best fix is usually at the source.
A hose or harness close to a header or turbo (strong radiant heat)T6 ThermaShield split tube or ThermaShield ConvolutedThe aluminized face reflects most of the radiant heat before it gets in, and the fiberglass behind it insulates against what does get through.
A firewall, floor pan, fuel cell or ECU box facing the exhaustThermaShield Flat or ThermaShield WrapThe same foil over fiberglass, as a sheet that sticks on or wraps around odd shapes.
Lines in a hot engine bay: steady heat soak, little direct radiant heatFireFlex fire sleeveA thick layer of fiberglass holds still air, which insulates; the silicone jacket seals out oil, fuel and splash. Leave at least 1/8" of air gap so the fiberglass is never squashed.
Single wires, sensor and thermocouple leads near heatInsultherm Tru-Fit fiberglass sleevingA thin fiberglass braid that insulates without adding bulk.
Plug wire boots close to the headersInsultherm spark plug boot sleevesDouble-thick fiberglass where the boot sits closest to the pipe.
Flame, sparks, weld spatter or molten splashDragon Sleeve, or FireFlex if the line also needs insulatingDragon fibre will not burn and shrugs off sparks, but its thin wall holds little air, so it does not insulate much. FireFlex resists splash and insulates.

All the lines compared:

ProductWhat it isHeat it handlesContinuous ratingHow it fitsBest for
Techflex FireFlex fire sleeveThick fiberglass braid with a silicone jacketDirect heat, open flame, oil and fuel splash500°F (260°C)Slides on before the hose ends go onFuel, oil, brake and clutch lines near headers or turbos
Techflex T6 ThermaShield split tubeAluminized fiberglass tube, split, closes with an adhesive stripReflects radiant heat491°F (255°C) material; reflects radiant heat from a 1,400°F source at 3/8"Wraps around: no need to remove fittingsAssembled hoses and harnesses near exhaust
Techflex ThermaShield ConvolutedSeamless aluminized fiberglass, flexible convoluted tubeReflects radiant heatNot publishedSlides onHoses and wires that bend in several directions
Techflex ThermaShield Flat (full adhesive)Flat aluminized fiberglass with a full adhesive backReflects radiant heatNot publishedSticks to any clean surfaceFirewalls, floor pans, fuel cells, ECU boxes
Techflex ThermaShield Wrap (adhesive edge)Flat aluminized fiberglass joined along one edge by adhesiveReflects radiant heatNot publishedWraps around odd shapesConnectors, sensors, short runs
Techflex Insultherm Tru-Fit fiberglass sleevingAcrylic-treated braided fiberglassDirect heat, no flame or fluid seal464°F (240°C)Slides onIndividual wires, thermocouple and sensor leads
Techflex Insultherm spark plug boot sleevesDouble-thick fiberglass sleeves, 7-1/2" longDirect heat at the header1,200°FSlips over the bootPlug wire boots close to headers
Techflex header wraps: Insultherm, Header Wrap SI, Volcano WrapWoven tape wrapped around the pipeKeeps heat inside the exhaustFiberglass 1,200°F; silica 2,000°F; basalt 1,300°FWrapped with 1/4" overlap, tied at the endsHeaders, down pipes, turbo crossovers
Techflex Dragon SleeveThin double-wall braid of non-flammable Dragon fibreFlame, sparks, weld spatter, molten splash; not an insulatorNone published; the fibre decomposes at 842°F (450°C)Slides on; the braid expandsLines and wires exposed to sparks or open flame
Techflex Weld Wrap HDSilicone-coated silica braid with hook-and-loop closureWeld spatter, slag, sparks; heat500°F (260°C) continuous; 2,000°F (1,093°C) intermittentWraps on with hook-and-loopWelding leads and hoses; lines that see sparks

Frequently asked questions

With or without the inner ring?

Both are 7-1/2" long, 3/4" across and rated the same. The ring version (FCU) has an inner ring at its open end; the plain version (FCN) has none.

Can the sleeve touch the header?

Yes. The maker says that once fitted the sleeve needs no clearance from hot surfaces and can rest directly on a header.

Will it fit a right-angle boot?

Yes. At 7-1/2" it covers straight and right-angle boots.

Ratings are the maker's published figures.