80.2 lb/hr Import Low-Z Fuel Injector
Quick Overview
- 80.2 lb/hr (606 g/min) at 3 bar, n-heptane
- Disc injector, Mark 6, Toyota-type inlet, 63.80-64.50 mm overall
- Low impedance, 2.2 ohms, peak and hold driver, EV1 (Minitimer) connector
- Spray: cone; O-rings 7.90 mm ID x 1.98 mm
- Flow-matched to 1% in packs (Buy In menu)
Show More
$58.30
per EACH (USD)80.2 lb/hr Import Low-Z Fuel Injector
01D143x - 80.2 lb/hr Low-Impedance Import Fuel Injector
Key features
- Low-impedance coil works with peak / hold injector drivers.
- High-speed disc action allows wider dynamic flow range for improved idling and quieter operation
- Design resists build up deposits which can affect fuel flow and cause clogging
- No fuel leakage for quicker starts
- Longer service life
- O-ring lubricant supplied
Specifications
| Part number | 01D143X |
| Static flow at 3 bar (43.5 psi) | 606 g/min (80.2 lb/hr), n-heptane |
| Flow, n-heptane basis | ~886 cc/min |
| Dynamic flow | 17.16 mg/pulse at 2.5 ms, 100 Hz, 14 V |
| Coil resistance | 2.2 ohms (low impedance) |
| Driver | Peak and hold (4A/1A) |
| Connector | EV1 (Jetronic / Minitimer) |
| Body style | Mark 6, Toyota-type inlet |
| Overall length | 63.80-64.50 mm overall |
| O-rings | 7.90 mm ID x 1.98 mm fluorocarbon |
| Spray | cone |
| Valve | Disc, top feed |
| SMP rating (gasoline equivalent) | 83 lb/hr (SMP's customer ID; this store rates injectors in n-heptane at 3 bar) |
| Static flow (as listed) | 80.2 lb/hr (606 grams/min) |
| Dynamic flow (as listed) | 17.16 mg/pulse |
| Coil resistance (as listed) | 2.2 Ohms |
| Spray pattern (as listed) | Cone |
| Connector type (as listed) | Minitimer (EV1-style) |
| Dynamic tollerance (as listed) | +/-6% |
| Peak / Hold current (as listed) | 4 / 1 Amps |
Dimensions and fitment
Flow rating and how it works
Flow rating: SMP labels this injector 83 lb/hr, a gasoline-equivalent figure. This store rates every injector in n-heptane at 3 bar (43.5 psi), where the SMP data sheet gives 606 g/min (80.2 lb/hr).
All tests run with n-Heptane @ 20°C (+/-1°C), 3.0 Bar (+/-0.01 Bar), 14VDC (+/-0.05VDC), peak and hold driver, 4A/1A peak/hold current. Dynamic rate @ 2.5ms @ 10ms period (100Hz)
Injector flow rates are based on testing with n-Heptane test solvent (0.6855 g/ml). U.S. EPA emission test gasoline 40CFR86.113 (0.735g/ml) flows in most common injector designs at about a 3 to 4% higher rate than n-Heptane. A ratio of 1.035:1 can be used when converting the flow specifications above.
Lookup chart: low-impedance injectors
Every SMP low-impedance (peak and hold) injector in this section. Flow is the static rating at 3 bar (43.5 psi): lb/hr from the rated g/min, cc/min on the n-heptane basis (g/min ÷ 0.684). This part is in bold. Click a column heading to sort; use the calculator below to mark the injectors that are big enough. On a phone, swipe the chart sideways.
| Part | Make | lb/hr | cc/min | Body | Length | Connector |
|---|---|---|---|---|---|---|
| 01D043X | SMP | 21.6 | 238 | Disc, Multec 1, extended nozzle | 74.8 mm overall (ref.) | EV1 (Jetronic / Minitimer) |
| 01D139X | SMP | 52.2 | 577 | Disc, Mark 5, 3000 series | 61.50-62.30 mm overall | EV1 (Jetronic / Minitimer) |
| 01D065X | SMP | 54.9* | 607* | Disc, Mark 6, Toyota-type inlet | 63.80-64.50 mm overall | EV1 (Jetronic / Minitimer) |
| 01D130X | SMP | 63.1 | 697 | Disc, Mark 6, Toyota-type inlet | 63.80-64.50 mm overall | EV1 (Jetronic / Minitimer) |
| 01D140X | SMP | 68.8 | 760 | Disc, Mark 5, 3000 series | 61.50-62.30 mm overall | EV1 (Jetronic / Minitimer) |
| 01D141X | SMP | 68.8 | 760 | Disc, Mark 6, Toyota-type inlet | 63.80-64.50 mm overall | EV1 (Jetronic / Minitimer) |
| 01D142X | SMP | 80.2 | 886 | Disc, Mark 5, 3000 series | 61.50-62.30 mm overall | EV1 (Jetronic / Minitimer) |
| 01D143X | SMP | 80.2 | 886 | Disc, Mark 6, Toyota-type inlet | 63.80-64.50 mm overall | EV1 (Jetronic / Minitimer) |
| 01D144X | SMP | 91.4 | 1010 | Disc, Mark 5, 3000 series | 61.50-62.30 mm overall | EV1 (Jetronic / Minitimer) |
| 01D145X | SMP | 91.4 | 1010 | Disc, Mark 6, Toyota-type inlet | 63.80-64.50 mm overall | EV1 (Jetronic / Minitimer) |
| 01D133X | SMP | 111.1 | 1228 | Disc, Mark 6, Toyota-type inlet | 63.80-64.50 mm overall | EV1 (Jetronic / Minitimer) |
| 01D134X | SMP | 111.1 | 1228 | Disc, Mark 5, 3000 series | 61.50-62.30 mm overall | EV1 (Jetronic / Minitimer) |
| 01D164X | SMP | 163.4 | 1806 | Disc, Mark 5, 3000 series | 61.50-62.30 mm overall | EV1 (Jetronic / Minitimer) |
SMP = Standard Motor Products disc injectors. The same SMP injectors are also sold under other brand names. * Rated in mineral spirits, not n-heptane. Lengths are overall length from the outline drawing. Low-impedance injectors need a peak and hold driver; for high-impedance injectors see the high-impedance section.
Injector size calculator
Enter your engine's numbers to find the injector size it needs. The result marks the big-enough injectors in the lookup chart above.
How the calculator works. Fuel needed (lb/hr) = crankshaft horsepower x brake specific fuel consumption (BSFC). Standard BSFC values (naturally aspirated / nitrous / turbocharged / supercharged): gasoline 0.50 / 0.55 / 0.60 / 0.65, E85 0.70 / 0.77 / 0.84 / 0.91, methanol 1.00 / 1.10 / 1.30 / 1.40. A supercharger takes power from the crank to drive it, so it needs more fuel per crank horsepower than a turbo. Methanol carries about 46% of gasoline's energy per pound, so it needs about twice the fuel. For an ethanol blend (E10 to E100), the fuel needed is worked out from the blend's stoichiometric air/fuel ratio (gasoline 14.7:1, ethanol 9.0:1, mixed by weight), scaled so that 85% ethanol gives the E85 values above; E100 comes out about 47% above gasoline. The standard values assume a typical air/fuel ratio for each fuel and set-up (for example 12.8:1 naturally aspirated and 11.5:1 boosted on gasoline); if you enter a target air/fuel ratio, the fuel is scaled to it. If you enter your own BSFC, it replaces the standard value and the air/fuel ratio entry is ignored. The fuel is split across the injectors and divided by the maximum duty cycle. With a static regulator, boost lowers the pressure across the injector (base pressure minus boost); a 1:1 referenced regulator keeps it at base pressure. The result is converted to the 43.5 psi (3 bar) rating with flow = rated flow x square root (pressure / 43.5). A wet nitrous kit supplies its own fuel through the nozzles, so choose the engine's base set-up for it. It is a starting point: your tuner should confirm injector size for your engine.
Parts that fit this injector
Racetronix parts that fit this injector. Each part links to its own page.
Injector driver or impedance converter (low-impedance injectors need a peak and hold driver, or a converter on a high-impedance ECU):
Connectors and pigtails (repair or rewire the injector plug):
Plug-and-play adapters (your car's injector plug to this injector):
- IA-UM: Injector Connector Wire Adapter - USCAR (EV6) to Minitimer (EV1)
- IA-HM: Injector Connector Wire Adapter - Honda to Minitimer (EV1)
- IA-M2M: Injector Connector Wire Adapter, Delphi Multec 2 to Minitimer (EV1)
- IA-NAM: Injector Connector Wire Adapter - Nippon Denso Type A to Minitimer (EV1)
- IA-NBM: Injector Connector Wire Adapter - Nippon Denso Type B to Minitimer (EV1)
- IA-TM: Injector Connector Wire Adapter - Toyota to Minitimer (EV1)
O-rings and filter:
- IFS-01: Filter Screen / Sock, Injector
Before you order
- Injectors sold in packs are dynamically flow-matched to within 1% tolerance.
- Injectors sold as each are as per factory tolerance specified.
- These are factory new injectors. We do not offer reconditioned / used injectors.
- * Advanced tuning data available in our support forum for confirmed Racetronix customers only.
- Absolutely no returns on open-box fuel injectors. Know your application before making your purchase.









