Banjo rubber hose fitting, -6 AN with -6 ORB banjo bolt
Quick Overview
- Rubber banjo hose end, -6 hose
- Compact 90-degree banjo, swivels on the bolt
- Reusable, for braided rubber hose
- Not for PTFE or push-lock hose
- E85 compatible, black anodized 6061-T6 aluminum
Show More
$32.96
per EACH (USD)Rubber Banjo Hose End, -6 Hose, with -6 AN ORB banjo bolt, Black
A compact banjo connection for -6 braided rubber hose.
The Racetronix FIT-100006 is a reusable banjo hose end for -6 braided rubber hose, with a -6 AN ORB banjo bolt. A banjo turns the line 90 degrees in very little space and swivels on its bolt, so you can aim the hose before tightening.
Key features
- -6 rubber hose end.
- Banjo: -6 AN ORB banjo bolt.
- Swivel: the eye turns on the bolt, so you can aim the hose before tightening.
- E85 compatible.
- 6061-T6 aluminum, black anodized.
The banjo seals on a washer each side of the eye; use new washers when refitting.
Specifications
| Part number | FIT-100006 |
| Hose size | -6 |
| Banjo | -6 AN ORB banjo bolt |
| Swivel | Yes, the eye turns on the bolt |
| Fits | Braided rubber (CPE) hose: Racetronix RBSH and RBNH and standard-bore equivalents |
| Includes | Nut (socket), banjo fitting head and banjo bolt |
| Material | 6061-T6 aluminum, black anodized |
| Fuel compatibility | Gasoline and E85 |
Tech drawing/schematic
Fits Racetronix RBSH stainless-braided and RBNH nylon-covered rubber hose, and standard-bore braided rubber (CPE) hose from other makers with standard AN inside and outside diameters. If you are not sure, compare the bore and outside diameter of your hose with ours. It does not fit PTFE hose, push-lock hose or nylon tube. For PTFE hose, use our PTFE hose ends.
The fitting is E85 compatible. The limit is the hose: although most CPE rubber hoses are rated for fuel, every CPE liner breaks down over time with fuel and solvents, and fuel smell around a parked vehicle is common. For long-term fuel lines we recommend our conductive-lined PTFE hose and PTFE hose ends. Rubber hose suits oil, coolant, vacuum and boost lines.
How it assembles
The hose end is two parts: the nut (socket) and the fitting head with its threaded nipple. There is no olive or ferrule.
- Wrap the cut mark in masking tape and cut the hose square with a thin cutting disc or fine-tooth saw. Trim any loose braid strands.
- Hold the nut in soft vise jaws and push the hose into it with a twisting motion until it bottoms against the step inside the nut.
- Mark the hose at the back of the nut with tape or a marker, so you can see if it pushes out while you tighten.
- Put a little grease on the nipple and its threads. We use silicone grease; wheel bearing grease also works.
- Start the fitting head into the nut by hand, then tighten with an aluminum AN wrench until the hexes are close (a gap of less than about 1/16" is normal). Check that the mark has not moved.
- Blow the hose out and check the assembly for leaks before you put it into service.
Questions? Ask on our support forum.
Lookup chart: rubber banjo hose ends
Every part in this series. This part is highlighted. Click a column heading to sort by it; click again to reverse. On a phone, swipe the chart sideways.
| Part number | Hose size | Banjo |
|---|---|---|
| FIT-100010LP | -10 hose | -10 AN ORB banjo bolt, low profile |
| FIT-R10B2215M | -10 hose | M22x1.5 banjo |
| FIT-100012LP | -12 hose | -12 AN ORB banjo bolt, low profile |
| FIT-100016LP | -16 hose | -16 AN ORB banjo bolt, low profile |
| FIT-100004 | -4 hose | -4 AN ORB banjo bolt |
| FIT-100004LP | -4 hose | -4 AN ORB banjo bolt, low profile |
| FIT-100006LP | -6 hose | -6 AN ORB banjo bolt, low profile |
| FIT-R10B2015M | -10 hose | M20x1.5 banjo |
| FIT-100012 | -12 hose | -12 AN ORB banjo bolt |
| FIT-100006 | -6 hose | -6 AN ORB banjo bolt |
| FIT-100008LP | -8 hose | -8 AN ORB banjo bolt, low profile |
Cross-reference: equivalent part numbers
The FIT-100006 replaces or compares with these parts from other brands. "Similar" means a close match that differs in a detail such as finish, swivel style or body type.
| Brand | Part number | Match |
|---|---|---|
| Fragola | 100006 | Equivalent |
| Vibrant | V1192 (-6 AN) | Similar |
About this cross-reference. We compiled these equivalent part numbers from the manufacturers’ published catalogs and websites, and we update them when we can. We have not fitted or tested other brands’ parts with ours. Please check the hose size, bore and end type against your application before you order, or email [email protected] and we’ll help. Final fitment is the buyer’s responsibility. Brand names and part numbers belong to their owners and are used for reference only; Racetronix is not affiliated with these companies.
Frequently asked questions
Will it fit my hose?
It fits Racetronix RBSH stainless-braided and RBNH nylon-covered rubber hose and other standard-bore braided rubber hose. It does not fit PTFE hose, push-lock hose or nylon tube. Compare bore and outside diameter if you are unsure.
Can I use it on PTFE hose?
No. PTFE hose needs a hose end with a ferrule (olive). See our PTFE hose ends.
Can I reuse it?
Yes. The nut and fitting head can be reused. To remake a joint, cut the hose back to fresh hose and assemble again.
Can I use it for fuel?
The fitting is E85 compatible. CPE rubber hose breaks down over time with fuel, so for long-term fuel lines we recommend PTFE hose and PTFE hose ends.
Is it E85 compatible?
Yes. It is made from 6061-T6 aluminum and black anodized, and works with gasoline and E85.
Questions and support
Not sure which fitting your build needs? Email [email protected] before you order.
Racetronix provides technical support to verified customers through our support forum, not by phone or email. Please request forum access when you place your order so your account is approved before your parts arrive. The forum is moderated, open 24/7, and holds a knowledge base going back to 1999.



















