The Racetronix FIT-CP6C is the aluminum crimp collar (socket) for Racetronix -6 PTFE crimp hose ends. It fits all Racetronix -6 PTFE hose. Every Racetronix aluminum PTFE crimp hose end comes with its collar; this is the replacement, for when you remake an end or need a spare.

Fits these -6 crimp hose ends: FIT-CP6F, FIT-CP6F45, FIT-CP6F90.

Key features

• Hose size: -6 smooth-bore PTFE hose.
• 16.1 mm outside diameter before crimping.
• Finished crimp OD: 14.1 mm on TFT-1167 and TFT-1170 hose, 14.1 mm on TFT-1165 and TFT-1168 hose.
• Aluminum.

Specifications

Current production may vary from the image.

Making a crimp assembly

1. Tape, then mark. Wrap masking tape tightly around the hose where you will cut, so the braid does not fray, then measure and mark the cut on the tape, allowing for the length each fitting adds.
2. Cut square through the mark with a thin cut-off wheel (the thin Bosch wheels work well), not a thick grinding wheel. Remove the tape and trim any stray braid wires flush.
3. Trim back any coating. On black covered (B) hose, cut the Hytrel or PVC coating back from the crimp area so the collar sits directly on the braid.
4. Clean the hose. Blast the cut end and the bore with brake cleaner, then blow it out with compressed air to clear all cutting debris.
5. Slide the collar onto the hose.
6. Push the nipple fully into the hose until the hose bottoms against the fitting, then bring the collar up against the fitting so it covers the nipple.
7. Line up angled ends first. Once crimped, the fitting cannot be turned on the hose, so line the angle up with the other end of the assembly and mark the hose and fitting before you crimp.
8. Crimp with a die that covers the collar size, following your crimper’s instructions, to the finished outside diameter in the crimp chart for your hose.
9. Measure the crimp with calipers in at least three places around the collar and compare it with the chart. If it is under size (over-crimped), cut it off and make a new end.
10. Flush and cap. Blow the finished assembly through with solvent and compressed air, cap both ends until it is installed, and pressure-test it before use.

Crimp chart: aluminum collars on Racetronix PTFE hose

Collar size before crimping and the finished outside diameter after crimping. Size -6 is highlighted. Crimp to the finished diameter, not to a die number.

All Racetronix PTFE crimp fittings

Every part in this series. This part is highlighted. Click a column heading to sort by it; click again to reverse. On a phone, swipe the chart sideways.

See all PTFE crimp fittings, reusable PTFE hose ends and Racetronix PTFE hose.

Cross-reference: equivalent part numbers

The FIT-CP6C replaces or compares with these parts from other brands. "Similar" means a close match that differs in a detail such as the hose it is made for, the crimp diameter, or whether the collar is included.

About this cross-reference. We compiled these equivalent part numbers from the manufacturers’ published catalogs and websites, and we update them when we can. We have not fitted or tested other brands’ parts with ours. Please check the hose size, bore and end type against your application before you order, or email [email protected] and we’ll help. Final fitment is the buyer’s responsibility. Brand names and part numbers belong to their owners and are used for reference only; Racetronix is not affiliated with these companies.

Frequently asked questions

Questions and support

Not sure which fitting your build needs? Email [email protected] before you order.

Racetronix provides technical support to verified customers through our support forum, not by phone or email. Please request forum access when you place your order so your account is approved before your parts arrive. The forum is moderated, open 24/7, and holds a knowledge base going back to 1999.