Welcome to Racetronix
Welcome to Racetronix  |  All prices indicated are in USD($)  905-477-7014  |   Help   |  Catalogs  |  About Us

Crimp Hose Fitting, Rubber 150° -6 AN JIC Female

Quick Overview

  • 150 deg crimp rubber hose end
  • -6 AN JIC female, 9/16 in.-18
  • For -6 braided rubber hose
  • Collar FIT-CRC06, crimp to 16.2 mm
  • 6061-T6 aluminum, black anodized

Show More
Item #: FIT-CR15FJ06

$20.21

per EACH (USD)
This is an obsolete Item
 
 
 In Stock & Ready to Ship

Crimp Hose End, 150° -6 AN JIC Female, Black

For -6 braided rubber hose, 150° bend, -6 AN JIC female (9/16"-18) end. Crimp collar FIT-CRC06 sold separately.

The Racetronix FIT-CR15FJ06 is a 150° crimp hose end for RBSH-6 stainless braided and RBNH-6 nylon covered -6 rubber hose, with a -6 AN JIC female end. It is crimped on with a FIT-CRC06 crimp collar and a hydraulic hose crimper, for a permanent, compact assembly.

The crimp chart below gives the collar size and the finished crimp diameter for each Racetronix hose. The chart near the bottom of the page lists every Racetronix crimp rubber hose end by size and angle.

Key features

  • Hose side: crimp nipple for -6 braided rubber hose (RBSH-6, RBNH-6).
  • AN end: -6 AN JIC female, 9/16"-18, 37° flare.
  • 150° bend, one-piece (non-swivel).
  • Crimp collar: FIT-CRC06 (sold separately), 17.85 mm before crimping.
  • Finished crimp OD: 16.2 mm on stainless braided hose, 16.2 mm on nylon covered hose.
  • 6061-T6 aluminum, black anodized.
Rubber hose and fuel

Many hose suppliers recommend rubber hose for fuel because the hose ends are easier to put on and the hose costs less. We don't, and that goes for every brand of CPE-lined rubber hose, ours included: it is the nature of the material, not the maker.

CPE liners deteriorate over time with the solvents and ethanol in today's fuels. Some race fuels oxygenated with MTBE (methyl tertiary butyl ether), or carrying other additives, can make the liner swell and narrow the bore like a clogged artery, or turn it soft and jelly-like. Pieces can then break off and plug injector filter baskets, fuel filters and the filter sock on the fuel pump.

Rubber hose is also permeable: fuel vapour escapes through it, which is why you smell fuel around a parked vehicle, and standard rubber and CPE hose is not CARB compliant. That is a large part of why carmakers moved away from rubber fuel hose in the late 1990s and early 2000s. CARB-compliant low-permeation hoses do exist, but they use specialized liners such as FKM (Viton) and usually cost more per foot than PTFE.

PTFE is a different material altogether: it resists these fuels and additives and is essentially impermeable to fuel and most solvents. (We do not sell it as CARB certified: certification applies to a tested, finished hose assembly, and ours are assembled by the customer.) For fuel lines, use our conductive-lined PTFE hose with PTFE hose ends. Braided rubber hose is a good choice for oil, coolant, vacuum and boost lines.

Specifications

Part numberFIT-CR15FJ06
Hose size-6 braided rubber hose, 11/32" ID
AN end-6 AN JIC female, 9/16"-18
Angle150°
SwivelNo. The angled ends are one piece: the whole fitting turns as you tighten the AN end.
Seal37° flare, metal to metal
Crimp collarFIT-CRC06 (sold separately)
Collar OD before crimping17.85 mm (0.703")
Finished crimp OD, stainless braided hose (RBSH-6)16.2 mm (0.638")
Finished crimp OD, nylon covered hose (RBNH-6)16.2 mm (0.638")
Material6061-T6 aluminum, black anodized
FIT-CR15FJ06 crimp rubber hose end

Current production may vary from the image.

The AN end seals metal to metal on its 37° flare, not on the threads. Do not put Teflon tape or thread sealant on it.

Making a crimp assembly

  1. Tape, then mark. Wrap masking tape tightly around the hose where you will cut, so the braid does not fray, then measure and mark the cut on the tape, allowing for the length each hose end adds.
  2. Cut square through the mark with a thin cut-off wheel (the thin Bosch wheels work well), not a thick grinding wheel. A slanted cut stops the hose bottoming on the fitting. Remove the tape and trim any stray braid wires.
  3. Clean the hose. Blast the cut end and the bore with a solvent such as brake cleaner, then blow it out with compressed air to clear all cutting debris.
  4. Slide the collar onto the hose.
  5. Grease the nipple only after cleaning. Put a little grease on the fitting nipple (we use silicone grease). Grease on an uncleaned hose traps rubber and braid debris inside the joint, where it can break loose and contaminate the system.
  6. Push the nipple fully into the hose until the hose bottoms against the fitting, then bring the collar up against the fitting so it covers the nipple.
  7. Line up angled ends first. Angled crimp ends do not swivel and cannot be turned once crimped, so line the angle up with the other end of the assembly and mark the hose and fitting before you crimp.
  8. Crimp with a die that covers the collar size, following your crimper’s instructions, to the finished outside diameter in the crimp chart for your hose.
  9. Measure the crimp with calipers in at least three places around the collar and compare it with the chart. If it is under size (over-crimped), cut it off and make a new end.
  10. Flush and cap. Blow the finished assembly through with solvent and compressed air, cap both ends until it is installed, and leak-check it before use.

Crimp chart: Racetronix rubber hose

Collar size before crimping and the finished outside diameter after crimping, for Racetronix braided rubber hose. Size -6 is highlighted. Crimp to the finished diameter, not to a die number.

Hose sizeCrimp collarCollar OD before crimpingFinished OD, stainless braided (RBSH)Finished OD, nylon covered (RBNH)
-4FIT-CRC0414.7 mm13.2 mm13.1 mm
-6FIT-CRC0617.85 mm16.2 mm16.2 mm
-8FIT-CRC0822.1 mm20.5 mm20.05 mm
-10FIT-CRC1025.7 mm23.6 mm23.6 mm
-12FIT-CRC1231.2 mm28.8 mm28.8 mm
-16FIT-CRC1635.1 mm32.8 mm32.5 mm
-20FIT-CRC2041.8 mm39.6 mm39.31 mm

All crimp rubber hose ends

Every Racetronix crimp hose end for braided rubber hose (58 parts). Rows are the hose size and end; columns are the angle. This part is in bold. Click a part number to open it. On a phone, swipe the chart sideways.

See all crimp rubber hose ends and reusable rubber hose ends.

Cross-reference: equivalent part numbers

The FIT-CR15FJ06 replaces or compares with these parts from other brands. "Similar" means a close match that differs in a detail such as finish, collar style, or whether the collar is included.

BrandPart numberMatch
Fragola3115006Equivalent
Earl'sAT715006ERLEquivalent
Russell610503Similar
XRPRC221506TDBBSimilar

About this cross-reference. We compiled these equivalent part numbers from the manufacturers’ published catalogs and websites, and we update them when we can. We have not fitted or tested other brands’ parts with ours. Please check the hose size, bore and end type against your application before you order, or email [email protected] and we’ll help. Final fitment is the buyer’s responsibility. Brand names and part numbers belong to their owners and are used for reference only; Racetronix is not affiliated with these companies.

Frequently asked questions

Is it E85 compatible?

The fitting is: it is 6061-T6 aluminum, black anodized. The rubber hose it goes on has a CPE liner, which is rated for E85, but the real question is for how long. For an E85 fuel system, use PTFE hose and PTFE hose ends.

Can I use it for fuel?

We do not recommend any brand of rubber hose for fuel. CPE liners deteriorate over time with ethanol and solvents, some race fuels with MTBE and other additives can make them swell or turn jelly-like and shed pieces into filters and injectors, and rubber hose lets fuel vapour through (it is not CARB compliant). For fuel lines, use our conductive PTFE hose, which is essentially impermeable to fuel, with PTFE hose ends.

Does it swivel?

No. The angled crimp ends are one piece and do not swivel, and once crimped the angle cannot be turned on the hose. Line the angle up with the other end of the hose assembly before you crimp.

Is the crimp collar included?

No. Order the FIT-CRC06 crimp collar with each hose end.

What crimper do I need?

A hydraulic hose crimper with a die set that covers the collar size. The fittings are not fussy about the crimper: what matters is reaching the finished outside diameter in the crimp chart. Check it with calipers after crimping.

What diameter do I crimp to?

On -6 Racetronix stainless braided hose (RBSH-6), 16.2 mm; on nylon covered hose (RBNH-6), 16.2 mm. The collar measures 17.85 mm before crimping.

Can I use it on PTFE or push-lock hose?

No. These crimp ends and collars are for braided rubber hose. PTFE hose takes PTFE hose ends, and push-lock hose takes push-lock fittings.

Do I need thread sealant?

No. The AN end seals on its 37° flare. Do not put Teflon tape or sealant on it.

Questions and support

Not sure which fitting your build needs? Email [email protected] before you order.

Racetronix provides technical support to verified customers through our support forum, not by phone or email. Please request forum access when you place your order so your account is approved before your parts arrive. The forum is moderated, open 24/7, and holds a knowledge base going back to 1999.

© 2026 Racetronix. All rights reserved. | Part No: FIT-CR15FJ06 | Revision: Alpha