Techflex FireFlex Silicone Fiberglass Fire Sleeve, 1-1/2” ID, Black
Quick Overview
- Techflex FireFlex fire sleeve, 1-1/2" (38.1 mm) ID, black
- Silicone-coated braided fiberglass, 500 degrees F (260 C) continuous
- Resists open flame, molten splash, oil and fuel
- Fits -16 rubber with an air gap
- Sold by the foot; slides on before the hose ends go on
Show More
$8.75
per Feet (USD)Techflex FireFlex Fire Sleeve, 1-1/2" (38.1 mm) ID, Black
Slides over hose, wire and cable: 500°F (260°C) continuous, resists open flame, molten splash and every common automotive fluid.

Techflex FireFlex is a thick braided fiberglass tube with a heavy silicone jacket. Racetronix is a Techflex distributor. It keeps fuel, oil, brake and clutch lines cooler and protects them from flame, splash and weld spatter. This is the 1-1/2" (38.1 mm) inside diameter, sold by the foot. Size it to the outside diameter of your hose, not its AN size: the chart below does that for every hose we sell, and the equivalents chart shows which other brands' fire sleeve each size replaces.
Key features
- 500°F (260°C) continuous, -65°F (-54°C) minimum. The glass fiber itself melts at 2,048°F (1,120°C).
- Silicone jacket resists fuel, oil, coolant, brake fluid and solvents, and sheds splash and spatter.
- Will not melt, delaminate or support combustion; completely non-conductive.
- Tough: in abrasion testing the coating lasted 4,800 cycles before the glass underneath showed any wear.
- Flexible: follows tight bends; cuts with scissors.
- Sold by the foot, black.
Which size fits my hose?
This size suits: -16 Stainless braided / nylon braided rubber hose.
Choose the sleeve whose inside diameter is at least 1/8" (3.2 mm) larger than the outside of your hose. Fire sleeve insulates with the air held in its glass braid, and it needs an air gap around the hose. A sleeve pulled tight over a hose compresses the fiberglass, squeezes out that air and loses much of its insulating value. The extra room also lets it slide on through bends. If the sleeve has to pass over a hose end that is already fitted, size it to the largest part of the fitting instead, or use the split aluminized tube, which wraps on.
Hose outside diameters are nominal values from our own hose pages. Hose with a black jacket or PVC cover is larger. Measure your hose if in doubt.
Fire sleeve chart: all sizes
| Part | Inside diameter | ID (mm) | Colour | Wall | For hose OD up to |
|---|---|---|---|---|---|
| 299-FIN0.25-BK | 1/4" | 6.3 | Black | 0.072" | 0.125" (3.2 mm) |
| 299-FIN0.38-BK | 3/8" | 9.5 | Black | 0.072" | 0.250" (6.3 mm) |
| 299-FIN0.50-BK | 1/2" | 12.7 | Black | 0.072" | 0.375" (9.5 mm) |
| 299-FIN0.63-BK | 5/8" | 15.9 | Black | 0.072" | 0.500" (12.7 mm) |
| 299-FIN0.75-BK | 3/4" | 19.0 | Black | 0.072" | 0.625" (15.9 mm) |
| 299-FIN0.75-RD | 3/4" | 19.0 | Red | 0.072" | 0.625" (15.9 mm) |
| 299-FIN0.88-BK | 7/8" | 22.2 | Black | 0.072" | 0.750" (19.0 mm) |
| 299-FIN1.00-BK | 1" | 25.4 | Black | 0.072" | 0.875" (22.2 mm) |
| 299-FIN1.25-BK | 1-1/4" | 31.8 | Black | 0.072" | 1.125" (28.6 mm) |
| 299-FIN1.50-BK | 1-1/2" | 38.1 | Black | 0.072" | 1.375" (34.9 mm) |
| 299-FIN1.75-BK | 1-3/4" | 44.4 | Black | 0.072" | 1.625" (41.3 mm) |
| 299-FIN2.00-BK | 2" | 50.8 | Black | 0.072" | 1.875" (47.6 mm) |
| 299-FIN2.38-BK | 2-3/8" | 60.3 | Black | 0.072" | 2.250" (57.1 mm) |
| 299-FIN2.88-BK | 2-7/8" | 73.0 | Black | 0.072" | 2.750" (69.8 mm) |
Equivalents: other brands' fire sleeve
Shopping for another brand? These are the same construction: silicone-coated braided fiberglass, rated 500°F continuous, in the same inside diameter.
| Our part | Instead of (brand) | Their part number | Description | Match |
|---|---|---|---|---|
| 299-FIN0.38-BK | DEI | 010470 | Fire Sleeve and Tape Kit, 3/8" x 3 ft | Same spec |
| 299-FIN0.38-BK | DEI | 092470 / 094470 | Fire Sleeve 3/8", 25 ft / 50 ft | Same spec |
| 299-FIN0.38-BK | Heatshield Products | 210010 / 210011 | Fire Shield Sleeve 3/8", red, 3 ft / 10 ft | Same spec |
| 299-FIN0.38-BK | Heatshield Products | 210040 / 210041 | Fire Shield Sleeve 3/8", black, 3 ft / 10 ft | Same spec |
| 299-FIN0.50-BK | Heatshield Products | 210012 / 210013 | Fire Shield Sleeve 1/2", red, 3 ft / 10 ft | Same spec |
| 299-FIN0.50-BK | Heatshield Products | 210042 / 210043 | Fire Shield Sleeve 1/2", black, 3 ft / 10 ft | Same spec |
| 299-FIN0.50-BK | Vibrant Performance | 25810 | Heat Protect Sleeving 1/2" x 5 ft | Same spec |
| 299-FIN0.63-BK | DEI | 010472 | Fire Sleeve and Tape Kit, 5/8" x 3 ft | Same spec |
| 299-FIN0.63-BK | DEI | 092472 / 094472 | Fire Sleeve 5/8", bulk | Same spec |
| 299-FIN0.63-BK | Vibrant Performance | 25815 | Heat Protect Sleeving 5/8" x 5 ft | Same spec |
| 299-FIN0.75-BK | DEI | 092473 / 093473 | Fire Sleeve 3/4", 25 ft / 50 ft | Same spec |
| 299-FIN0.75-BK | Heatshield Products | 210014 / 210015 | Fire Shield Sleeve 3/4", red, 3 ft / 10 ft | Same spec |
| 299-FIN0.75-BK | Heatshield Products | 210044 / 210045 | Fire Shield Sleeve 3/4", black, 3 ft / 10 ft | Same spec |
| 299-FIN0.75-BK | Vibrant Performance | 25811 | Heat Protect Sleeving 3/4" x 5 ft | Same spec |
| 299-FIN0.88-BK | Vibrant Performance | 25812 | Heat Protect Sleeving 7/8" x 5 ft | Same spec |
| 299-FIN1.00-BK | DEI | 010474 | Fire Sleeve and Tape Kit, 1" x 3 ft | Same spec |
| 299-FIN1.00-BK | DEI | 092474 / 094474 | Fire Sleeve 1", bulk | Same spec |
| 299-FIN1.00-BK | Heatshield Products | 210016 / 210017 | Fire Shield Sleeve 1", red, 3 ft / 10 ft | Same spec |
| 299-FIN1.00-BK | Heatshield Products | 210046 / 210047 | Fire Shield Sleeve 1", black, 3 ft / 10 ft | Same spec |
| 299-FIN1.00-BK | Vibrant Performance | 25813 | Heat Protect Sleeving 1" x 5 ft | Same spec |
| 299-FIN1.25-BK | Heatshield Products | 210018 / 210019 | Fire Shield Sleeve 1-1/4", red, 3 ft / 10 ft | Same spec |
| 299-FIN1.25-BK | Heatshield Products | 210048 / 210049 | Fire Shield Sleeve 1-1/4", black, 3 ft / 10 ft | Same spec |
| 299-FIN1.25-BK | Vibrant Performance | 25816 | Heat Protect Sleeving 1-1/4" x 5 ft | Same spec |
| 299-FIN1.50-BK | Heatshield Products | 210020 / 210021 | Fire Shield Sleeve 1-1/2", red, 3 ft / 10 ft | Same spec |
| 299-FIN1.50-BK | Heatshield Products | 210050 / 210051 | Fire Shield Sleeve 1-1/2", black, 3 ft / 10 ft | Same spec |
| 299-FIN1.50-BK | Vibrant Performance | 25817 | Heat Protect Sleeving 1-1/2" x 5 ft | Same spec |
Other brands' names and part numbers are their owners' trademarks, listed only to help you compare. Check sizes against your application.
Specifications
| Construction | Braided fiberglass, silicone rubber jacket |
| Inside diameter | 1-1/2" (38.1 mm) |
| Wall | 0.072" (1.8 mm) |
| Continuous temperature | -65°F to 500°F (-54°C to 260°C) |
| Flammability | Non-flammable |
| Chemical resistance | No effect from fuels, oils, hydraulic fluid, solvents, salt water; little effect from strong acids and oxidizers |
| Cutting | Scissors or a sharp knife |
| Sold by | The foot |
Installing fire sleeve
- Cut the sleeve about 1" longer than the hose between the fittings.
- Fit one hose end. Slide the sleeve over the hose, then fit the other end. On short hoses, push the sleeve back on itself to make room for the second fitting, then work it back.
- Pull the sleeve up to each fitting and secure the ends with stainless hose clamps or ties so it cannot slide off the hot area.
- Keep the cut ends clean and sealed so fluid cannot wick into the glass braid.
Crimp the fittings onto the bare hose, never over the sleeve.
Which heat protection do I need?
Heat reaches a hose or wire in three ways, and each needs a different kind of protection.
- Radiant heat. A header or turbo throws heat out in every direction, like a stove element, and it reaches anything in line of sight. Reflective foil stops it best: the aluminized face bounces it back before it gets in.
- Heat soak. Hot air and nearby hot parts warm a line slowly and steadily. Insulation stops it. Braided fiberglass traps thousands of tiny pockets of still air, the same way the insulation in a house wall does, and still air carries heat very poorly. Squash the fiberglass and the air goes, and most of the insulation with it.
- Flame, sparks and splash. A burst line, a backfire or weld spatter. This needs a covering that will not burn: a silicone jacket or a non-flammable fibre.
Foil-over-fiberglass products combine the first two: the foil reflects, the fiberglass insulates. Nothing should rest against a bare header; wrap the header, shield the line, or both.
| Situation | Use | Why it works |
|---|---|---|
| The exhaust itself: headers, down pipes, turbo crossovers | Header wrap | Keeps the heat inside the pipe, so far less of it radiates onto the hoses, wiring and bodywork around it. The best fix is usually at the source. |
| A hose or harness close to a header or turbo (strong radiant heat) | T6 ThermaShield split tube or ThermaShield Convoluted | The aluminized face reflects most of the radiant heat before it gets in, and the fiberglass behind it insulates against what does get through. |
| A firewall, floor pan, fuel cell or ECU box facing the exhaust | ThermaShield Flat or ThermaShield Wrap | The same foil over fiberglass, as a sheet that sticks on or wraps around odd shapes. |
| Lines in a hot engine bay: steady heat soak, little direct radiant heat | FireFlex fire sleeve | A thick layer of fiberglass holds still air, which insulates; the silicone jacket seals out oil, fuel and splash. Leave at least 1/8" of air gap so the fiberglass is never squashed. |
| Single wires, sensor and thermocouple leads near heat | Insultherm Tru-Fit fiberglass sleeving | A thin fiberglass braid that insulates without adding bulk. |
| Plug wire boots close to the headers | Insultherm spark plug boot sleeves | Double-thick fiberglass where the boot sits closest to the pipe. |
| Flame, sparks, weld spatter or molten splash | Dragon Sleeve, or FireFlex if the line also needs insulating | Dragon fibre will not burn and shrugs off sparks, but its thin wall holds little air, so it does not insulate much. FireFlex resists splash and insulates. |
All the lines compared:
| Product | What it is | Heat it handles | Continuous rating | How it fits | Best for |
|---|---|---|---|---|---|
| Techflex FireFlex fire sleeve | Thick fiberglass braid with a silicone jacket | Direct heat, open flame, oil and fuel splash | 500°F (260°C) | Slides on before the hose ends go on | Fuel, oil, brake and clutch lines near headers or turbos |
| Techflex T6 ThermaShield split tube | Aluminized fiberglass tube, split, closes with an adhesive strip | Reflects radiant heat | 491°F (255°C) material; reflects radiant heat from a 1,400°F source at 3/8" | Wraps around: no need to remove fittings | Assembled hoses and harnesses near exhaust |
| Techflex ThermaShield Convoluted | Seamless aluminized fiberglass, flexible convoluted tube | Reflects radiant heat | Not published | Slides on | Hoses and wires that bend in several directions |
| Techflex ThermaShield Flat (full adhesive) | Flat aluminized fiberglass with a full adhesive back | Reflects radiant heat | Not published | Sticks to any clean surface | Firewalls, floor pans, fuel cells, ECU boxes |
| Techflex ThermaShield Wrap (adhesive edge) | Flat aluminized fiberglass joined along one edge by adhesive | Reflects radiant heat | Not published | Wraps around odd shapes | Connectors, sensors, short runs |
| Techflex Insultherm Tru-Fit fiberglass sleeving | Acrylic-treated braided fiberglass | Direct heat, no flame or fluid seal | 464°F (240°C) | Slides on | Individual wires, thermocouple and sensor leads |
| Techflex Insultherm spark plug boot sleeves | Double-thick fiberglass sleeves, 7-1/2" long | Direct heat at the header | 1,200°F | Slips over the boot | Plug wire boots close to headers |
| Techflex header wraps: Insultherm, Header Wrap SI, Volcano Wrap | Woven tape wrapped around the pipe | Keeps heat inside the exhaust | Fiberglass 1,200°F; silica 2,000°F; basalt 1,300°F | Wrapped with 1/4" overlap, tied at the ends | Headers, down pipes, turbo crossovers |
| Techflex Dragon Sleeve | Thin double-wall braid of non-flammable Dragon fibre | Flame, sparks, weld spatter, molten splash; not an insulator | None published; the fibre decomposes at 842°F (450°C) | Slides on; the braid expands | Lines and wires exposed to sparks or open flame |
Frequently asked questions
Do I pick the sleeve by the AN size of the hose?
No. The size of fire sleeve is its inside diameter. Hose of the same AN size has different outside diameters depending on how it is made: -6 PTFE hose is 0.445", -6 stainless braided rubber hose is 0.559" and -6 push-lock is 0.63". Use the chart above.
Can I slit the sleeve to fit it over an assembled hose?
No: a slit sleeve opens up in the heat and no longer seals. Use the split aluminized tube, which is made to wrap on and close with its adhesive strip.
Will it go over the hose ends?
Only if its inside diameter is larger than the fitting. Normally the sleeve goes on between the fittings and is clamped up to them.
Does a bigger sleeve insulate better?
A sleeve with some room insulates better than one stretched tight, because the glass fibers stay loose. Leave at least 1/8" between the hose and the inside of the sleeve; more is fine, as long as the sleeve does not flop about and catch on things.
Should I also wrap the header?
Yes, where a line runs within a few inches of a header. Header wrap keeps the heat in the pipe and the sleeve protects the line from what gets out.
Ratings are the maker's published figures. Fire sleeve protects a line from heat; it does not make a damaged or leaking line safe.


