Welcome to Racetronix
Welcome to Racetronix  |  All prices indicated are in USD($)  905-477-7014  |   Help   |  Catalogs  |  About Us

Techflex FireFlex Silicone Fiberglass Fire Sleeve, 7/8” ID, Black

Quick Overview

  • Techflex FireFlex fire sleeve, 7/8" (22.2 mm) ID, black
  • Silicone-coated braided fiberglass, 500 degrees F (260 C) continuous
  • Resists open flame, molten splash, oil and fuel
  • Fits -8 rubber, -10 PTFE, -6 push-lock, -8 push-lock and 5/8" hard line with an air gap
  • Sold by the foot; slides on before the hose ends go on

Show More
Item #: 299-FIN0.88-BK  MPN : FIN0.88-BK

$5.14

per Feet (USD)
This is an obsolete Item
 
 
 In Stock & Ready to Ship

Techflex FireFlex Fire Sleeve, 7/8" (22.2 mm) ID, Black

Slides over hose, wire and cable: 500°F (260°C) continuous, resists open flame, molten splash and every common automotive fluid.

Techflex FireFlex fire sleeve, black, showing the silicone jacket and the fiberglass braid inside

Techflex FireFlex is a thick braided fiberglass tube with a heavy silicone jacket. Racetronix is a Techflex distributor. It keeps fuel, oil, brake and clutch lines cooler and protects them from flame, splash and weld spatter. This is the 7/8" (22.2 mm) inside diameter, sold by the foot. Size it to the outside diameter of your hose, not its AN size: the chart below does that for every hose we sell, and the equivalents chart shows which other brands' fire sleeve each size replaces.

Key features

  • 500°F (260°C) continuous, -65°F (-54°C) minimum. The glass fiber itself melts at 2,048°F (1,120°C).
  • Silicone jacket resists fuel, oil, coolant, brake fluid and solvents, and sheds splash and spatter.
  • Will not melt, delaminate or support combustion; completely non-conductive.
  • Tough: in abrasion testing the coating lasted 4,800 cycles before the glass underneath showed any wear.
  • Flexible: follows tight bends; cuts with scissors.
  • Sold by the foot, black.

Which size fits my hose?

This size suits: -8 Stainless braided / nylon braided rubber hose; -10 PTFE hose, stainless braid; -10 PTFE hose, nylon over-braid; -6 Push-lock hose; -8 Push-lock hose; 5/8" Aluminum hard line.

Choose the sleeve whose inside diameter is at least 1/8" (3.2 mm) larger than the outside of your hose. Fire sleeve insulates with the air held in its glass braid, and it needs an air gap around the hose. A sleeve pulled tight over a hose compresses the fiberglass, squeezes out that air and loses much of its insulating value. The extra room also lets it slide on through bends. If the sleeve has to pass over a hose end that is already fitted, size it to the largest part of the fitting instead, or use the split aluminized tube, which wraps on.

Hose or lineSizeHose OD (in)Hose OD (mm)Fire sleeve to useRoom (in)
Stainless braided / nylon braided rubber hose-40.441"11.25/8" (299-FIN0.63-BK)0.184"
Stainless braided / nylon braided rubber hose-60.559"14.23/4" (299-FIN0.75-BK)0.191"
Stainless braided / nylon braided rubber hose-80.673"17.17/8" (299-FIN0.88-BK)0.202"
Stainless braided / nylon braided rubber hose-100.819"20.81" (299-FIN1.00-BK)0.181"
Stainless braided / nylon braided rubber hose-120.961"24.41-1/4" (299-FIN1.25-BK)0.289"
Stainless braided / nylon braided rubber hose-161.201"30.51-1/2" (299-FIN1.50-BK)0.299"
Stainless braided / nylon braided rubber hose-201.409"35.81-3/4" (299-FIN1.75-BK)0.341"
PTFE hose, stainless braid-30.252"6.41/2" (299-FIN0.50-BK)0.248"
PTFE hose, stainless braid-40.311"7.91/2" (299-FIN0.50-BK)0.189"
PTFE hose, stainless braid-60.445"11.35/8" (299-FIN0.63-BK)0.180"
PTFE hose, stainless braid-80.547"13.93/4" (299-FIN0.75-BK)0.203"
PTFE hose, stainless braid-100.650"16.57/8" (299-FIN0.88-BK)0.225"
PTFE hose, stainless braid-120.776"19.71" (299-FIN1.00-BK)0.224"
PTFE hose, stainless braid-161.031"26.21-1/4" (299-FIN1.25-BK)0.219"
PTFE hose, nylon over-braid-30.252"6.41/2" (299-FIN0.50-BK)0.248"
PTFE hose, nylon over-braid-40.311"7.91/2" (299-FIN0.50-BK)0.189"
PTFE hose, nylon over-braid-60.421"10.75/8" (299-FIN0.63-BK)0.204"
PTFE hose, nylon over-braid-80.547"13.93/4" (299-FIN0.75-BK)0.203"
PTFE hose, nylon over-braid-100.626"15.97/8" (299-FIN0.88-BK)0.249"
PTFE hose, nylon over-braid-120.768"19.51" (299-FIN1.00-BK)0.232"
Push-lock hose-40.470"11.95/8" (299-FIN0.63-BK)0.155"
Push-lock hose5/16"0.560"14.23/4" (299-FIN0.75-BK)0.190"
Push-lock hose-60.630"16.07/8" (299-FIN0.88-BK)0.245"
Push-lock hose-80.750"19.07/8" (299-FIN0.88-BK)0.125"
Push-lock hose-100.940"23.91-1/4" (299-FIN1.25-BK)0.310"
Push-lock hose-121.000"25.41-1/4" (299-FIN1.25-BK)0.250"
Aluminum hard line1/4"0.250"6.33/8" (299-FIN0.38-BK)0.125"
Aluminum hard line5/16"0.313"7.91/2" (299-FIN0.50-BK)0.187"
Aluminum hard line3/8"0.375"9.55/8" (299-FIN0.63-BK)0.250"
Aluminum hard line1/2"0.500"12.75/8" (299-FIN0.63-BK)0.125"
Aluminum hard line5/8"0.625"15.97/8" (299-FIN0.88-BK)0.250"

Hose outside diameters are nominal values from our own hose pages. Hose with a black jacket or PVC cover is larger. Measure your hose if in doubt.

Fire sleeve chart: all sizes

PartInside diameterID (mm)ColourWallFor hose OD up to
299-FIN0.25-BK1/4"6.3Black0.072"0.125" (3.2 mm)
299-FIN0.38-BK3/8"9.5Black0.072"0.250" (6.3 mm)
299-FIN0.50-BK1/2"12.7Black0.072"0.375" (9.5 mm)
299-FIN0.63-BK5/8"15.9Black0.072"0.500" (12.7 mm)
299-FIN0.75-BK3/4"19.0Black0.072"0.625" (15.9 mm)
299-FIN0.75-RD3/4"19.0Red0.072"0.625" (15.9 mm)
299-FIN0.88-BK7/8"22.2Black0.072"0.750" (19.0 mm)
299-FIN1.00-BK1"25.4Black0.072"0.875" (22.2 mm)
299-FIN1.25-BK1-1/4"31.8Black0.072"1.125" (28.6 mm)
299-FIN1.50-BK1-1/2"38.1Black0.072"1.375" (34.9 mm)
299-FIN1.75-BK1-3/4"44.4Black0.072"1.625" (41.3 mm)
299-FIN2.00-BK2"50.8Black0.072"1.875" (47.6 mm)
299-FIN2.38-BK2-3/8"60.3Black0.072"2.250" (57.1 mm)
299-FIN2.88-BK2-7/8"73.0Black0.072"2.750" (69.8 mm)

Equivalents: other brands' fire sleeve

Shopping for another brand? These are the same construction: silicone-coated braided fiberglass, rated 500°F continuous, in the same inside diameter.

Our partInstead of (brand)Their part numberDescriptionMatch
299-FIN0.38-BKDEI010470Fire Sleeve and Tape Kit, 3/8" x 3 ftSame spec
299-FIN0.38-BKDEI092470 / 094470Fire Sleeve 3/8", 25 ft / 50 ftSame spec
299-FIN0.38-BKHeatshield Products210010 / 210011Fire Shield Sleeve 3/8", red, 3 ft / 10 ftSame spec
299-FIN0.38-BKHeatshield Products210040 / 210041Fire Shield Sleeve 3/8", black, 3 ft / 10 ftSame spec
299-FIN0.50-BKHeatshield Products210012 / 210013Fire Shield Sleeve 1/2", red, 3 ft / 10 ftSame spec
299-FIN0.50-BKHeatshield Products210042 / 210043Fire Shield Sleeve 1/2", black, 3 ft / 10 ftSame spec
299-FIN0.50-BKVibrant Performance25810Heat Protect Sleeving 1/2" x 5 ftSame spec
299-FIN0.63-BKDEI010472Fire Sleeve and Tape Kit, 5/8" x 3 ftSame spec
299-FIN0.63-BKDEI092472 / 094472Fire Sleeve 5/8", bulkSame spec
299-FIN0.63-BKVibrant Performance25815Heat Protect Sleeving 5/8" x 5 ftSame spec
299-FIN0.75-BKDEI092473 / 093473Fire Sleeve 3/4", 25 ft / 50 ftSame spec
299-FIN0.75-BKHeatshield Products210014 / 210015Fire Shield Sleeve 3/4", red, 3 ft / 10 ftSame spec
299-FIN0.75-BKHeatshield Products210044 / 210045Fire Shield Sleeve 3/4", black, 3 ft / 10 ftSame spec
299-FIN0.75-BKVibrant Performance25811Heat Protect Sleeving 3/4" x 5 ftSame spec
299-FIN0.88-BKVibrant Performance25812Heat Protect Sleeving 7/8" x 5 ftSame spec
299-FIN1.00-BKDEI010474Fire Sleeve and Tape Kit, 1" x 3 ftSame spec
299-FIN1.00-BKDEI092474 / 094474Fire Sleeve 1", bulkSame spec
299-FIN1.00-BKHeatshield Products210016 / 210017Fire Shield Sleeve 1", red, 3 ft / 10 ftSame spec
299-FIN1.00-BKHeatshield Products210046 / 210047Fire Shield Sleeve 1", black, 3 ft / 10 ftSame spec
299-FIN1.00-BKVibrant Performance25813Heat Protect Sleeving 1" x 5 ftSame spec
299-FIN1.25-BKHeatshield Products210018 / 210019Fire Shield Sleeve 1-1/4", red, 3 ft / 10 ftSame spec
299-FIN1.25-BKHeatshield Products210048 / 210049Fire Shield Sleeve 1-1/4", black, 3 ft / 10 ftSame spec
299-FIN1.25-BKVibrant Performance25816Heat Protect Sleeving 1-1/4" x 5 ftSame spec
299-FIN1.50-BKHeatshield Products210020 / 210021Fire Shield Sleeve 1-1/2", red, 3 ft / 10 ftSame spec
299-FIN1.50-BKHeatshield Products210050 / 210051Fire Shield Sleeve 1-1/2", black, 3 ft / 10 ftSame spec
299-FIN1.50-BKVibrant Performance25817Heat Protect Sleeving 1-1/2" x 5 ftSame spec

Other brands' names and part numbers are their owners' trademarks, listed only to help you compare. Check sizes against your application.

Specifications

ConstructionBraided fiberglass, silicone rubber jacket
Inside diameter7/8" (22.2 mm)
Wall0.072" (1.8 mm)
Continuous temperature-65°F to 500°F (-54°C to 260°C)
FlammabilityNon-flammable
Chemical resistanceNo effect from fuels, oils, hydraulic fluid, solvents, salt water; little effect from strong acids and oxidizers
CuttingScissors or a sharp knife
Sold byThe foot

Installing fire sleeve

  1. Cut the sleeve about 1" longer than the hose between the fittings.
  2. Fit one hose end. Slide the sleeve over the hose, then fit the other end. On short hoses, push the sleeve back on itself to make room for the second fitting, then work it back.
  3. Pull the sleeve up to each fitting and secure the ends with stainless hose clamps or ties so it cannot slide off the hot area.
  4. Keep the cut ends clean and sealed so fluid cannot wick into the glass braid.
Crimp hose ends

Crimp the fittings onto the bare hose, never over the sleeve.

Which heat protection do I need?

Heat reaches a hose or wire in three ways, and each needs a different kind of protection.

  • Radiant heat. A header or turbo throws heat out in every direction, like a stove element, and it reaches anything in line of sight. Reflective foil stops it best: the aluminized face bounces it back before it gets in.
  • Heat soak. Hot air and nearby hot parts warm a line slowly and steadily. Insulation stops it. Braided fiberglass traps thousands of tiny pockets of still air, the same way the insulation in a house wall does, and still air carries heat very poorly. Squash the fiberglass and the air goes, and most of the insulation with it.
  • Flame, sparks and splash. A burst line, a backfire or weld spatter. This needs a covering that will not burn: a silicone jacket or a non-flammable fibre.

Foil-over-fiberglass products combine the first two: the foil reflects, the fiberglass insulates. Nothing should rest against a bare header; wrap the header, shield the line, or both.

SituationUseWhy it works
The exhaust itself: headers, down pipes, turbo crossoversHeader wrapKeeps the heat inside the pipe, so far less of it radiates onto the hoses, wiring and bodywork around it. The best fix is usually at the source.
A hose or harness close to a header or turbo (strong radiant heat)T6 ThermaShield split tube or ThermaShield ConvolutedThe aluminized face reflects most of the radiant heat before it gets in, and the fiberglass behind it insulates against what does get through.
A firewall, floor pan, fuel cell or ECU box facing the exhaustThermaShield Flat or ThermaShield WrapThe same foil over fiberglass, as a sheet that sticks on or wraps around odd shapes.
Lines in a hot engine bay: steady heat soak, little direct radiant heatFireFlex fire sleeveA thick layer of fiberglass holds still air, which insulates; the silicone jacket seals out oil, fuel and splash. Leave at least 1/8" of air gap so the fiberglass is never squashed.
Single wires, sensor and thermocouple leads near heatInsultherm Tru-Fit fiberglass sleevingA thin fiberglass braid that insulates without adding bulk.
Plug wire boots close to the headersInsultherm spark plug boot sleevesDouble-thick fiberglass where the boot sits closest to the pipe.
Flame, sparks, weld spatter or molten splashDragon Sleeve, or FireFlex if the line also needs insulatingDragon fibre will not burn and shrugs off sparks, but its thin wall holds little air, so it does not insulate much. FireFlex resists splash and insulates.

All the lines compared:

ProductWhat it isHeat it handlesContinuous ratingHow it fitsBest for
Techflex FireFlex fire sleeveThick fiberglass braid with a silicone jacketDirect heat, open flame, oil and fuel splash500°F (260°C)Slides on before the hose ends go onFuel, oil, brake and clutch lines near headers or turbos
Techflex T6 ThermaShield split tubeAluminized fiberglass tube, split, closes with an adhesive stripReflects radiant heat491°F (255°C) material; reflects radiant heat from a 1,400°F source at 3/8"Wraps around: no need to remove fittingsAssembled hoses and harnesses near exhaust
Techflex ThermaShield ConvolutedSeamless aluminized fiberglass, flexible convoluted tubeReflects radiant heatNot publishedSlides onHoses and wires that bend in several directions
Techflex ThermaShield Flat (full adhesive)Flat aluminized fiberglass with a full adhesive backReflects radiant heatNot publishedSticks to any clean surfaceFirewalls, floor pans, fuel cells, ECU boxes
Techflex ThermaShield Wrap (adhesive edge)Flat aluminized fiberglass joined along one edge by adhesiveReflects radiant heatNot publishedWraps around odd shapesConnectors, sensors, short runs
Techflex Insultherm Tru-Fit fiberglass sleevingAcrylic-treated braided fiberglassDirect heat, no flame or fluid seal464°F (240°C)Slides onIndividual wires, thermocouple and sensor leads
Techflex Insultherm spark plug boot sleevesDouble-thick fiberglass sleeves, 7-1/2" longDirect heat at the header1,200°FSlips over the bootPlug wire boots close to headers
Techflex header wraps: Insultherm, Header Wrap SI, Volcano WrapWoven tape wrapped around the pipeKeeps heat inside the exhaustFiberglass 1,200°F; silica 2,000°F; basalt 1,300°FWrapped with 1/4" overlap, tied at the endsHeaders, down pipes, turbo crossovers
Techflex Dragon SleeveThin double-wall braid of non-flammable Dragon fibreFlame, sparks, weld spatter, molten splash; not an insulatorNone published; the fibre decomposes at 842°F (450°C)Slides on; the braid expandsLines and wires exposed to sparks or open flame

Frequently asked questions

Do I pick the sleeve by the AN size of the hose?

No. The size of fire sleeve is its inside diameter. Hose of the same AN size has different outside diameters depending on how it is made: -6 PTFE hose is 0.445", -6 stainless braided rubber hose is 0.559" and -6 push-lock is 0.63". Use the chart above.

Can I slit the sleeve to fit it over an assembled hose?

No: a slit sleeve opens up in the heat and no longer seals. Use the split aluminized tube, which is made to wrap on and close with its adhesive strip.

Will it go over the hose ends?

Only if its inside diameter is larger than the fitting. Normally the sleeve goes on between the fittings and is clamped up to them.

Does a bigger sleeve insulate better?

A sleeve with some room insulates better than one stretched tight, because the glass fibers stay loose. Leave at least 1/8" between the hose and the inside of the sleeve; more is fine, as long as the sleeve does not flop about and catch on things.

Should I also wrap the header?

Yes, where a line runs within a few inches of a header. Header wrap keeps the heat in the pipe and the sleeve protects the line from what gets out.

Ratings are the maker's published figures. Fire sleeve protects a line from heat; it does not make a damaged or leaking line safe.