Welcome to Racetronix
Welcome to Racetronix  |  All prices indicated are in USD($)  905-477-7014  |   Help   |  Catalogs  |  About Us

Weld Bung, 1/2-20 Female, Aluminum

Item #: BUNG-1220AL

$4.19

per EACH (USD)
This is an obsolete Item
 
 
 In Stock & Ready to Ship

Weld Bung, 1/2-20 Female, Aluminum

Weld-in aluminum bung that adds a 1/2"-20 UNF female port to an aluminum tank, pan or tube.

The Racetronix BUNG-1220AL is a weld bung: it is welded into a fuel tank, oil pan, catch can, intercooler pipe or other aluminum part to add a 1/2"-20 UNF female O-ring port (same thread as -5 AN ORB). It is aluminum, so weld it only to aluminum. The weld pilot fits a hole drilled to its diameter (C on the drawing) so the bung sits square while you weld.

Key features

  • 1/2"-20 UNF female O-ring port (same thread as -5 AN ORB).
  • Round, flanged body.
  • 6061-T6 aluminum, bare (unfinished) for clean welding.
  • E85 compatible.
O-ring seal

The port seals on the O-ring of the male fitting against the port face. Do not use tape or thread sealant.

Specifications

Part numberBUNG-1220AL
Connection1/2"-20 UNF female O-ring port (same thread as -5 AN ORB)
BodyRound, flanged
Material6061-T6 aluminum, bare (unfinished) for welding
MountingWeld-in (weld to aluminum only)
Dimensions (inches, see drawing)A 0.50 · B 0.94 · C 0.81 · D 0.55

Tech drawing/schematic

Racetronix BUNG-1220AL weld bung series drawing and dimension chart

Series drawing: every part in this section, with dimensions. Click the drawing to enlarge. All dimensions in inches.

Lookup chart

Every bung in this section. Click a column heading to sort by it; click again to reverse. Dimensions in inches (A overall length, B flange diameter, C weld pilot diameter, D O-ring seat diameter); a dash means the dimension is not on the drawing.

Part numberConnectionABCD
BUNG-1220AL1/2"-20 UNF female0.500.940.810.55

Welding and installation

  • Weld aluminum bungs only to aluminum. Aluminum bungs are TIG welded.
  • Drill the mounting hole to the weld pilot diameter (C) so the bung locates square, then tack it in place before welding all the way around.
  • Thread a scrap fitting or plug into the bung while welding to help keep the threads and sealing surface true, and let it cool before removing it.
  • Clean out any weld spatter and debris, and pressure- or leak-test the part before it goes into service.

General guidance only. Welding should be done by a qualified welder following safe practice: never weld on a fuel tank that has held fuel unless it has been properly purged and made safe.

Frequently asked questions

Which material do I need?

Match the bung to the part you weld it to: aluminum to aluminum, mild steel to mild steel, stainless to stainless. Aluminum cannot be welded to steel.

Do I need thread sealant?

No. The O-ring on the male fitting seals against the port face.

What thread is it?

1/2"-20 UNF, the same straight thread as a -5 AN ORB port.

Questions and support

Not sure which bung your build needs? Email [email protected] before you order.

Racetronix provides technical support to verified customers through our support forum, not by phone or email. Please request forum access when you place your order so your account is approved before your parts arrive. The forum is moderated, open 24/7, and holds a knowledge base going back to 1999.

© 2026 Racetronix. All rights reserved. | Part No: BUNG-1220AL | Revision: Alpha