C43 Fuel Pump Assembly - Factory Upgrade
FPA-009 - 1984-1985 C4 Corvette Fuel Pump Assembly - Factory Upgrade 180LPH
- Walbro 180L/Hr Pump
- Filter sock - 30 micron filtering (factory=70 micron)
- Walbro to GM direct power wiring (no adapters)
- Terminal lock
- High pressure fuel line
- Stainless gear clamps
- Rubber pump mount
- Pump sound insulation sleeve
- C4 fuel tank gasket
- Stainless hex-head tank bolts, washers and o-ring seals ( 9 pieces)
- Hex key
- Silicone grease
Walbro sets set the industry standard in high-performance in-tank pumps. Walbro pumps are used as factory equipment in performance vehicles such as the C5 & C6 Corvette. Walbro's gerotor design is able to maintain high volume at elevated pressures. This is done by squeezing the fuel out between two gears instead of pushing it like most factory vane pumps. The positive displacement gerotor design makes high-performance Walbro pumps small, light weight, quiet, efficient and reliable. Racetronix offers this kit bundled with the GSS242M 190L/Hr pump or the FPA-009H kit bundled with the GSS340M 255L/Hr pump. The GSS242M is capable of supporting approximately 450RWHP* @ 13.5V through factory lines. The GSS340M is capable of supporting approximately 550RWHP* @ 13.5V through factory lines. (* HP numbers will vary based on engine and driveline efficiency, operating pressure and pump voltage.)
Pump Installation kit- Racetronix Exclusive!
Walbro does not manufacture a fuel pump installation kit specifically for the C4 Corvette. Walbro's 400-835 and 400-1016 fuel pump installation kits which are normally bundled with the GSS340M and F20000169 pumps are tailored towards 1980's g-body and b-body fuel senders. Racetronix has bundled together a C4 specific fuel pump installation kit which includes a few upgrades such as a sound insulation sleeve, one-piece teflon in-tank wiring harness, C4 tank gasket and stainless sender bolts with o-rings. The factory pump came with a sound insulation sleeve so we have included one. This sleeve helps reduce pump noise heard from outside the tank. Racetronix has manufactured a quality C4 tank gasket and bundled it with new stainless steel tank bolts and o-rings. Most C4 tank gaskets are in pretty bad shape and will not provide a proper vapor seal. The factory black-oxide sender bolts are typically rusted and their o-rings have deteriorated. These bolts must be in good condition and their o-rings intact to achieve a vapor seal as they extend into the gas tank. GM fuel sender gasket (P/N 25091503) lists at $15.25. The fuel sender bolts with o-rings (P/N 14044556) list at $45.54 for a set of nine. A total value of $60.79 included at no extra charge. Racetronix supplied bolts and tank gasket are made from superior materials. A hex key is included to aid in the installation of the stainless sender bolts.
In-tank Wiring - Racetronix Exclusive!
In-tank wiring is quickly becoming a major problem due to the age of the C4's. Many terminals are heavily corroded or rusting off.
The generic in-tank wiring adapters supplied with other installation kits rely on the questionable factory wiring and adds another connection to the equation. This translates to more resistance / voltage loss and an extra potential failure point. Racetronix in-house harness manufacturing facility has produced a one-piece replacement for the in-tank pump wiring. Racetronix replacement in-tank wiring plugs directly into the new pump and into the factory bulkhead connector thereby eliminating all the factory pump wiring and the need for in-line plug adapters. The Racetronix harness is made with thicker 14 gauge Teflon wire vs. the factory's 16 gauge wire. Teflon is the most resistant to gas and solvents. All connections are assembled using our computerized crimp-quality monitoring system and then circuit checked for the utmost in reliability.