Welcome to Racetronix
Welcome to Racetronix  |  All prices indicated are in USD($)  905-477-7014  |   Help   |  Catalogs  |  About Us

63.1 lb/hr disc low-impedance import fuel injector

Quick Overview

  • 63.1 lb/hr (477 g/min) at 3 bar, n-heptane
  • Disc injector, Mark 6, Toyota-type inlet, 63.80-64.50 mm overall
  • Low impedance, 2.2 ohms, peak and hold driver, EV1 (Minitimer) connector
  • Spray: 3-hole insert; O-rings 7.90 mm ID x 1.98 mm
  • Sold individually, factory tolerance

Show More
Item #: 01D130x

$60.36

per EACH (USD)
This is an obsolete Item
 
 
 In Stock & Ready to Ship

63.1 lb/hr disc low-impedance import fuel injector

01D130x - 63.1 lb/hr Low-Impedance Import Fuel Injector

Flow at 3 bar63.1 lb/hr477 g/min · ~697 cc/min n-heptane
BodyDisc, Mark 6, Toyota-type inlet63.80-64.50 mm overall
ConnectorEV1 (Jetronic / Minitimer)
Resistance2.2 ohmsLow impedance, peak and hold

Key features

  • Low-impedance coil works with peak / hold injector drivers.
  • High-speed disc action allows wider dynamic flow range for improved idling and quieter operation
  • Design resists build up deposits which can affect fuel flow and cause clogging
  • No fuel leakage for quicker starts
  • Longer service life
  • O-ring lubricant supplied

Specifications

Part number01D130X
Static flow at 3 bar (43.5 psi)477 g/min (63.1 lb/hr), n-heptane
Flow, n-heptane basis~697 cc/min
Dynamic flow14.61 mg/pulse at 2.5 ms, 100 Hz, 14 V
Coil resistance2.2 ohms (low impedance)
DriverPeak and hold (2A/0.5A)
ConnectorEV1 (Jetronic / Minitimer)
Body styleMark 6, Toyota-type inlet
Overall length63.80-64.50 mm overall
O-rings7.90 mm ID x 1.98 mm fluorocarbon
Spray3-hole insert
ValveDisc, top feed
Mineral spirits rating500 g/min (66.1 lb/hr) in mineral spirits at 3 bar, the earlier rating on this page
Static flow (as listed)66.1 lb/hr (500 grams/min)
Dynamic flow (as listed)14.63 mg/pulse
Coil resistance (as listed)2.2 Ohms
Spray pattern (as listed)Cone
Connector type (as listed)Minitimer (EV1-style)
Dynamic tollerance (as listed)+/-6%

Dimensions and fitment

01D130X injector outline drawing with dimensions

Click the drawing to enlarge. Dimensions in millimeters. Body style: Mark 6, Toyota-type inlet.

Flow rating and how it works

All tests run with n-Heptane @ 20°C (+/-1°C), 3.0 Bar (+/-0.01 Bar), 14VDC (+/-0.05VDC), peak and hold driver, 2A/0.5A peak/hold current. Dynamic rate @ 2.5ms @ 10ms period (100Hz)

Injector flow rates are based on testing with n-Heptane test solvent (0.6855 g/ml). U.S. EPA emission test gasoline 40CFR86.113 (0.735g/ml) flows in most common injector designs at about a 3 to 4% higher rate than n-Heptane. A ratio of 1.035:1 can be used when converting the flow specifications above.

Lookup chart: low-impedance injectors

Every SMP low-impedance (peak and hold) injector in this section. Flow is the static rating at 3 bar (43.5 psi): lb/hr from the rated g/min, cc/min on the n-heptane basis (g/min ÷ 0.684). This part is in bold. Click a column heading to sort; use the calculator below to mark the injectors that are big enough. On a phone, swipe the chart sideways.

PartMakelb/hrcc/minBodyLengthConnector
01D043XSMP21.6238Disc, Multec 1, extended nozzle74.8 mm overall (ref.)EV1 (Jetronic / Minitimer)
01D139XSMP52.2577Disc, Mark 5, 3000 series61.50-62.30 mm overallEV1 (Jetronic / Minitimer)
01D065XSMP54.9*607*Disc, Mark 6, Toyota-type inlet63.80-64.50 mm overallEV1 (Jetronic / Minitimer)
01D130XSMP63.1697Disc, Mark 6, Toyota-type inlet63.80-64.50 mm overallEV1 (Jetronic / Minitimer)
01D140XSMP68.8760Disc, Mark 5, 3000 series61.50-62.30 mm overallEV1 (Jetronic / Minitimer)
01D141XSMP68.8760Disc, Mark 6, Toyota-type inlet63.80-64.50 mm overallEV1 (Jetronic / Minitimer)
01D142XSMP80.2886Disc, Mark 5, 3000 series61.50-62.30 mm overallEV1 (Jetronic / Minitimer)
01D143XSMP80.2886Disc, Mark 6, Toyota-type inlet63.80-64.50 mm overallEV1 (Jetronic / Minitimer)
01D144XSMP91.41010Disc, Mark 5, 3000 series61.50-62.30 mm overallEV1 (Jetronic / Minitimer)
01D145XSMP91.41010Disc, Mark 6, Toyota-type inlet63.80-64.50 mm overallEV1 (Jetronic / Minitimer)
01D133XSMP111.11228Disc, Mark 6, Toyota-type inlet63.80-64.50 mm overallEV1 (Jetronic / Minitimer)
01D134XSMP111.11228Disc, Mark 5, 3000 series61.50-62.30 mm overallEV1 (Jetronic / Minitimer)
01D164XSMP163.41806Disc, Mark 5, 3000 series61.50-62.30 mm overallEV1 (Jetronic / Minitimer)

SMP = Standard Motor Products disc injectors. The same SMP injectors are also sold under other brand names. * Rated in mineral spirits, not n-heptane. Lengths are overall length from the outline drawing. Low-impedance injectors need a peak and hold driver; for high-impedance injectors see the high-impedance section.

Injector size calculator

Enter your engine's numbers to find the injector size it needs. The result marks the big-enough injectors in the lookup chart above.

How the calculator works. Fuel needed (lb/hr) = crankshaft horsepower x brake specific fuel consumption (BSFC). Standard BSFC values (naturally aspirated / nitrous / turbocharged / supercharged): gasoline 0.50 / 0.55 / 0.60 / 0.65, E85 0.70 / 0.77 / 0.84 / 0.91, methanol 1.00 / 1.10 / 1.30 / 1.40. A supercharger takes power from the crank to drive it, so it needs more fuel per crank horsepower than a turbo. Methanol carries about 46% of gasoline's energy per pound, so it needs about twice the fuel. For an ethanol blend (E10 to E100), the fuel needed is worked out from the blend's stoichiometric air/fuel ratio (gasoline 14.7:1, ethanol 9.0:1, mixed by weight), scaled so that 85% ethanol gives the E85 values above; E100 comes out about 47% above gasoline. The standard values assume a typical air/fuel ratio for each fuel and set-up (for example 12.8:1 naturally aspirated and 11.5:1 boosted on gasoline); if you enter a target air/fuel ratio, the fuel is scaled to it. If you enter your own BSFC, it replaces the standard value and the air/fuel ratio entry is ignored. The fuel is split across the injectors and divided by the maximum duty cycle. With a static regulator, boost lowers the pressure across the injector (base pressure minus boost); a 1:1 referenced regulator keeps it at base pressure. The result is converted to the 43.5 psi (3 bar) rating with flow = rated flow x square root (pressure / 43.5). A wet nitrous kit supplies its own fuel through the nozzles, so choose the engine's base set-up for it. It is a starting point: your tuner should confirm injector size for your engine.

Parts that fit this injector

Racetronix parts that fit this injector. Each part links to its own page.

Injector driver or impedance converter (low-impedance injectors need a peak and hold driver, or a converter on a high-impedance ECU):

  • IDM4: Injector Driver Module 4-Channel
  • ICS-4H: Impedance Converter System Honda

Connectors and pigtails (repair or rewire the injector plug):

  • ICA8: Injector Connector Assembly Minitimer
  • RCS-008: Connector Set, Injector Minitimer

Plug-and-play adapters (your car's injector plug to this injector):

  • IA-UM: Injector Connector Wire Adapter - USCAR (EV6) to Minitimer (EV1)
  • IA-HM: Injector Connector Wire Adapter - Honda to Minitimer (EV1)
  • IA-M2M: Injector Connector Wire Adapter, Delphi Multec 2 to Minitimer (EV1)
  • IA-NAM: Injector Connector Wire Adapter - Nippon Denso Type A to Minitimer (EV1)
  • IA-NBM: Injector Connector Wire Adapter - Nippon Denso Type B to Minitimer (EV1)
  • IA-TM: Injector Connector Wire Adapter - Toyota to Minitimer (EV1)

O-rings and filter:

  • IFS-01: Filter Screen / Sock, Injector

Before you order

© 2026 Racetronix. All rights reserved. | Part No: 01D130X | Revision: Bravo