52.2 lb/hr low-impedance fuel injector
Quick Overview
- 52.2 lb/hr (395 g/min) at 3 bar, n-heptane
- Disc injector, Mark 5, 3000 series, 61.50-62.30 mm overall
- Low impedance, 2.2 ohms, peak and hold driver, EV1 (Minitimer) connector
- Spray: 3-hole insert; O-rings 7.80 mm ID x 3.60 mm
- Flow-matched to 1% in packs (Buy In menu)
Show More
$52.71
per EACH (USD)52.2 lb/hr low-impedance fuel injector
01D139x - 52.2 lb/hr Low Impedance Fuel Injector
Key features
Typical applications
- High-performance aftermarket
Specifications
| Part number | 01D139X |
| Static flow at 3 bar (43.5 psi) | 395 g/min (52.2 lb/hr), n-heptane |
| Flow, n-heptane basis | ~577 cc/min |
| Dynamic flow | 12.00 mg/pulse at 2.5 ms, 100 Hz, 14 V |
| Coil resistance | 2.2 ohms (low impedance) |
| Driver | Peak and hold (4A/1A) |
| Connector | EV1 (Jetronic / Minitimer) |
| Body style | Mark 5, 3000 series |
| Overall length | 61.50-62.30 mm overall |
| O-rings | 7.80 mm ID x 3.60 mm fluorocarbon, top and bottom |
| Spray | 3-hole insert |
| Valve | Disc, top feed |
| SMP rating (gasoline equivalent) | 55 lb/hr (SMP's customer ID; this store rates injectors in n-heptane at 3 bar) |
Dimensions and fitment
Flow rating and how it works
Flow rating: SMP labels this injector 55 lb/hr, a gasoline-equivalent figure. This store rates every injector in n-heptane at 3 bar (43.5 psi), where the SMP data sheet gives 395 g/min (52.2 lb/hr).
All tests run with n-Heptane @ 20°C (+/-1°C), 3.0 Bar (+/-0.01 Bar), 14VDC (+/-0.05VDC), peak and hold driver, 4A/1A peak/hold current.
Injector flow rates are based on testing with n-Heptane test solvent (0.6855 g/ml). U.S. EPA emission test gasoline 40CFR86.113 (0.735g/ml) flows in most common injector designs at about a 3 to 4% higher rate than n-Heptane. A ratio of 1.035:1 can be used when converting the flow specifications above.
This low-impedance injector is designed to work with peak and hold injector drivers typically found in aftermarket ECM/PCMs as well as dedicated injector driver modules sold by Racetronix..
Top feed disc injectors use a small disc with six holes around its circumference. The disc rests on a short chimney that surrounds a metering hole. As the disc is raised off the chimney by magnetic force, fuel flows through the holes in the disc, over the walls of the chimney, and out the metering hole to form a full, finely atomized cone.
- The flat mating surface ensures that no excess fuel is present to evaporate and therefore, no deposits or clogging can occur
- Longer service life
- High-speed disc action allows wider dynamic flow range for improved idling
Quieter operation
- Revolutionary disc design resists build up deposits which can affect fuel flow
- No Fuel leakage for quicker starts
- Compatible with alternative fuels (i.e. E85, Methanol)
- Grease supplied to lubricate o-rings prior to installation
Lookup chart: low-impedance injectors
Every SMP low-impedance (peak and hold) injector in this section. Flow is the static rating at 3 bar (43.5 psi): lb/hr from the rated g/min, cc/min on the n-heptane basis (g/min ÷ 0.684). This part is in bold. Click a column heading to sort; use the calculator below to mark the injectors that are big enough. On a phone, swipe the chart sideways.
| Part | Make | lb/hr | cc/min | Body | Length | Connector |
|---|---|---|---|---|---|---|
| 01D043X | SMP | 21.6 | 238 | Disc, Multec 1, extended nozzle | 74.8 mm overall (ref.) | EV1 (Jetronic / Minitimer) |
| 01D139X | SMP | 52.2 | 577 | Disc, Mark 5, 3000 series | 61.50-62.30 mm overall | EV1 (Jetronic / Minitimer) |
| 01D065X | SMP | 54.9* | 607* | Disc, Mark 6, Toyota-type inlet | 63.80-64.50 mm overall | EV1 (Jetronic / Minitimer) |
| 01D130X | SMP | 63.1 | 697 | Disc, Mark 6, Toyota-type inlet | 63.80-64.50 mm overall | EV1 (Jetronic / Minitimer) |
| 01D140X | SMP | 68.8 | 760 | Disc, Mark 5, 3000 series | 61.50-62.30 mm overall | EV1 (Jetronic / Minitimer) |
| 01D141X | SMP | 68.8 | 760 | Disc, Mark 6, Toyota-type inlet | 63.80-64.50 mm overall | EV1 (Jetronic / Minitimer) |
| 01D142X | SMP | 80.2 | 886 | Disc, Mark 5, 3000 series | 61.50-62.30 mm overall | EV1 (Jetronic / Minitimer) |
| 01D143X | SMP | 80.2 | 886 | Disc, Mark 6, Toyota-type inlet | 63.80-64.50 mm overall | EV1 (Jetronic / Minitimer) |
| 01D144X | SMP | 91.4 | 1010 | Disc, Mark 5, 3000 series | 61.50-62.30 mm overall | EV1 (Jetronic / Minitimer) |
| 01D145X | SMP | 91.4 | 1010 | Disc, Mark 6, Toyota-type inlet | 63.80-64.50 mm overall | EV1 (Jetronic / Minitimer) |
| 01D133X | SMP | 111.1 | 1228 | Disc, Mark 6, Toyota-type inlet | 63.80-64.50 mm overall | EV1 (Jetronic / Minitimer) |
| 01D134X | SMP | 111.1 | 1228 | Disc, Mark 5, 3000 series | 61.50-62.30 mm overall | EV1 (Jetronic / Minitimer) |
| 01D164X | SMP | 163.4 | 1806 | Disc, Mark 5, 3000 series | 61.50-62.30 mm overall | EV1 (Jetronic / Minitimer) |
SMP = Standard Motor Products disc injectors. The same SMP injectors are also sold under other brand names. * Rated in mineral spirits, not n-heptane. Lengths are overall length from the outline drawing. Low-impedance injectors need a peak and hold driver; for high-impedance injectors see the high-impedance section.
Injector size calculator
Enter your engine's numbers to find the injector size it needs. The result marks the big-enough injectors in the lookup chart above.
How the calculator works. Fuel needed (lb/hr) = crankshaft horsepower x brake specific fuel consumption (BSFC). Standard BSFC values (naturally aspirated / nitrous / turbocharged / supercharged): gasoline 0.50 / 0.55 / 0.60 / 0.65, E85 0.70 / 0.77 / 0.84 / 0.91, methanol 1.00 / 1.10 / 1.30 / 1.40. A supercharger takes power from the crank to drive it, so it needs more fuel per crank horsepower than a turbo. Methanol carries about 46% of gasoline's energy per pound, so it needs about twice the fuel. For an ethanol blend (E10 to E100), the fuel needed is worked out from the blend's stoichiometric air/fuel ratio (gasoline 14.7:1, ethanol 9.0:1, mixed by weight), scaled so that 85% ethanol gives the E85 values above; E100 comes out about 47% above gasoline. The standard values assume a typical air/fuel ratio for each fuel and set-up (for example 12.8:1 naturally aspirated and 11.5:1 boosted on gasoline); if you enter a target air/fuel ratio, the fuel is scaled to it. If you enter your own BSFC, it replaces the standard value and the air/fuel ratio entry is ignored. The fuel is split across the injectors and divided by the maximum duty cycle. With a static regulator, boost lowers the pressure across the injector (base pressure minus boost); a 1:1 referenced regulator keeps it at base pressure. The result is converted to the 43.5 psi (3 bar) rating with flow = rated flow x square root (pressure / 43.5). A wet nitrous kit supplies its own fuel through the nozzles, so choose the engine's base set-up for it. It is a starting point: your tuner should confirm injector size for your engine.
Parts that fit this injector
Racetronix parts that fit this injector. Each part links to its own page.
Injector driver or impedance converter (low-impedance injectors need a peak and hold driver, or a converter on a high-impedance ECU):
Connectors and pigtails (repair or rewire the injector plug):
Plug-and-play adapters (your car's injector plug to this injector):
- IA-UM: Injector Connector Wire Adapter - USCAR (EV6) to Minitimer (EV1)
- IA-HM: Injector Connector Wire Adapter - Honda to Minitimer (EV1)
- IA-M2M: Injector Connector Wire Adapter, Delphi Multec 2 to Minitimer (EV1)
- IA-NAM: Injector Connector Wire Adapter - Nippon Denso Type A to Minitimer (EV1)
- IA-NBM: Injector Connector Wire Adapter - Nippon Denso Type B to Minitimer (EV1)
- IA-TM: Injector Connector Wire Adapter - Toyota to Minitimer (EV1)
O-rings and filter:
Before you order
- Dynamically flowed and grouped to within 1% tolerance using Racetronix custom injector flow bench when purchased in packs.
- FLOW-MATCHED 1% INJECTORS ARE SOLD IN PACKS VIA THE 'BUY IN' DROP-DOWN MENU ABOVE.
- INJECTORS SOLD AS EACH ARE NOT FLOW-MATCHED (LISTED FACTORY TOLERANCE APPLIES)
- Absolutely no returns on open-box fuel injectors. Know your application before making your purchase.












